D-Link DGS-3700 User Manual
DGS-3700-12/DGS-3700-12G Series Layer 2 Gigabit Ethernet Switch User Manual
93
Time
Query Interval
(1-65535)
(1-65535)
The Query Interval field is used to set the time (in seconds) between transmitting IGMP
queries. Entries between 1 and 65535 seconds are allowed. Default = 125.
queries. Entries between 1 and 65535 seconds are allowed. Default = 125.
Max Response
Time
(1-25)
Time
(1-25)
This determines the maximum amount of time in seconds allowed before sending an IGMP
response report. The Max Response Time field allows an entry between 1 and 25 (seconds).
Default = 10.
response report. The Max Response Time field allows an entry between 1 and 25 (seconds).
Default = 10.
Robustness Value
(1-255)
(1-255)
Adjust this variable according to expected packet loss. If packet loss on the VLAN is expected
to be high, the Robustness Variable should be increased to accommodate increased packet
loss. This entry field allows an entry of 1 to 255. Default = 2.
to be high, the Robustness Variable should be increased to accommodate increased packet
loss. This entry field allows an entry of 1 to 255. Default = 2.
Last Member
Query Interval
(1-25 Sec)
Query Interval
(1-25 Sec)
This field specifies the maximum amount of time between group-specific query messages,
including those sent in response to leave group messages. Default = 1.
including those sent in response to leave group messages. Default = 1.
Data Driven Group
Expiry Time (1-
65535)
Expiry Time (1-
65535)
Allows the user to set the time that an IGMP Snooping data driven learning group will expire for
the specified VLAN.
the specified VLAN.
Querier State
Choose Enabled to enable transmitting IGMP Query packets or Disabled to disable. The
default is Disabled.
default is Disabled.
Fast Leave
This parameter allows the user to enable the Fast Leave function. Enabled, this function will
allow members of a multicast group to leave the group immediately (without the
implementation of the Last Member Query Timer) when an IGMP Leave Report Packet is
received by the Switch. The default is Disabled.
allow members of a multicast group to leave the group immediately (without the
implementation of the Last Member Query Timer) when an IGMP Leave Report Packet is
received by the Switch. The default is Disabled.
State
Select Enabled to implement IGMP Snooping. This field is Disabled by default.
Report
Suppression
Suppression
Select Enable or Disable for IGMP Snooping report suppression for specified VLANs.
Data Driven
Learning State
Learning State
Allows users to enable or disable IGMP snooping data driven learning for the specified VLAN.
Data Driven
Learning Aged Out
Learning Aged Out
Allows users to enable or disable aged_out of IGMP Snooping data driven learning for the
specified VLAN.
specified VLAN.
Version
Allows the user to configure the IGMP version used on the Switch. The default value is 3.
Querier Role
This read-only field describes the behavior of the router for sending query packets. Querier will
denote that the router is sending out IGMP query packets. Non-Querier will denote that the
router is not sending out IGMP query packets. This field will only read Querier when the
Querier State and the State fields have been Enabled.
denote that the router is sending out IGMP query packets. Non-Querier will denote that the
router is not sending out IGMP query packets. This field will only read Querier when the
Querier State and the State fields have been Enabled.
To modify the IGMP Snooping Router IP Settings click on the hyperlinked
Modify Router Port
which will show the
following window for the user to configure:
Figure 3 - 30 IGMP Snooping Router IP Settings – Edit window