DELL 9.8(0.0) User Manual
You can activate flow-based monitoring for a monitoring session by entering the
flow-based enable command in the Monitor Session mode. When you enable
this capability, traffic with particular flows that are traversing through the ingress
and egress interfaces are examined and, appropriate ACLs can be applied in both
the ingress and egress direction. Flow-based monitoring conserves bandwidth by
monitoring only specified traffic instead all traffic on the interface. This feature is
particularly useful when looking for malicious traffic. It is available for Layer 2 and
Layer 3 ingress and egress traffic. You may specify traffic using standard or
extended access-lists. This mechanism copies all incoming or outgoing packets on
one port and forwards (mirrors) them to another port. The source port is the
monitored port (MD) and the destination port is the monitoring port (MG).
flow-based enable command in the Monitor Session mode. When you enable
this capability, traffic with particular flows that are traversing through the ingress
and egress interfaces are examined and, appropriate ACLs can be applied in both
the ingress and egress direction. Flow-based monitoring conserves bandwidth by
monitoring only specified traffic instead all traffic on the interface. This feature is
particularly useful when looking for malicious traffic. It is available for Layer 2 and
Layer 3 ingress and egress traffic. You may specify traffic using standard or
extended access-lists. This mechanism copies all incoming or outgoing packets on
one port and forwards (mirrors) them to another port. The source port is the
monitored port (MD) and the destination port is the monitoring port (MG).
permit ether-type (for Extended MAC ACLs)
Configure a filter that allows traffic with specified types of Ethernet packets. This command is supported
only on 12-port GE line cards with SFP optics. For specifications, refer to your line card documentation.
Syntax
permit ether-type protocol-type-number {destination-mac-address
mac-address-mask | any} vlan vlan-id {source-mac-address mac-
address-mask | any} [count [byte]] [order] [log [interval
minutes] [threshold-in-msgs [count]] [monitor]
To remove this filter, you have two choices:
mac-address-mask | any} vlan vlan-id {source-mac-address mac-
address-mask | any} [count [byte]] [order] [log [interval
minutes] [threshold-in-msgs [count]] [monitor]
To remove this filter, you have two choices:
• Use the no seq sequence-number command if you know the filter’s
sequence number.
• Use the no permit ether-type protocol-type-number
{destination-mac-address mac-address-mask | any} vlan vlan-
id {source-mac-address mac-address-mask | any} command.
id {source-mac-address mac-address-mask | any} command.
Parameters
log
(OPTIONAL) Enter the keyword log to enable the triggering
of ACL log messages.
of ACL log messages.
threshold-in
msgs count
msgs count
(OPTIONAL) Enter the threshold-in-msgs keyword
followed by a value to indicate the maximum number of ACL
logs that can be generated, exceeding which the generation
of ACL logs is terminated. with the seq, permit, or deny
commands. The threshold range is from 1 to 100.
followed by a value to indicate the maximum number of ACL
logs that can be generated, exceeding which the generation
of ACL logs is terminated. with the seq, permit, or deny
commands. The threshold range is from 1 to 100.
interval
minutes
minutes
(OPTIONAL) Enter the keyword interval followed by the
time period in minutes at which ACL logs must be generated.
The interval range is from 1 to 10 minutes.
time period in minutes at which ACL logs must be generated.
The interval range is from 1 to 10 minutes.
monitor
(OPTIONAL) Enter the keyword monitor when the rule is
describing the traffic that you want to monitor and the ACL
in which you are creating the rule is applied to the monitored
interface.
describing the traffic that you want to monitor and the ACL
in which you are creating the rule is applied to the monitored
interface.
Access Control Lists (ACL)
341