3com 4210 PWR 9-Port User Manual
Introduction to the Switch 4210 Family PWR Switches
13
The Switch 4210 PWR
Front Panel LEDs
Power LED
Table 3 describes the power LED on the Switch 4210 PWR model.
10/100BASE-TX Autosensing Ethernet Port Status LED
There are two port status LEDs on both sides (yellow LED on the left and green LED
on the right) of the 10/100BASE-TX Ethernet port on the Switch 4210 PWR
models. They indicate the port’s active, link, duplex, and speed status.
on the right) of the 10/100BASE-TX Ethernet port on the Switch 4210 PWR
models. They indicate the port’s active, link, duplex, and speed status.
In addition, there is an A/L LED and a D/S LED on each Switch 4210 PWR model.
These two LEDs indicate the port status LEDs mode. When the A/L LED is on, the
port status LEDs respectively indicate the port’s active status and link status. When
the D/S LED is on, the port status LEDs respectively indicate the port’s duplex status
and speed status. Either the A/L LED or the D/S LED is on at one time. For details,
see Table 4.
These two LEDs indicate the port status LEDs mode. When the A/L LED is on, the
port status LEDs respectively indicate the port’s active status and link status. When
the D/S LED is on, the port status LEDs respectively indicate the port’s duplex status
and speed status. Either the A/L LED or the D/S LED is on at one time. For details,
see Table 4.
You can change the mode of the port status LEDs by pressing the Mode button.
After a switch is powered on, the A/L LED is on initially. If you press the Mode
button, the D/S LED will be on. After that, if you press the Mode button again
within 45 seconds, the A/L LED will be on again. Otherwise, the A/L LED will
automatically be on 45 seconds later.
After a switch is powered on, the A/L LED is on initially. If you press the Mode
button, the D/S LED will be on. After that, if you press the Mode button again
within 45 seconds, the A/L LED will be on again. Otherwise, the A/L LED will
automatically be on 45 seconds later.
1000 Mbps Uplink Port Status LED
Table 5 describes the 1000 Mbps upline port status LED on the Switch 4210.
Table 3 The power LED on the Switch 4210 PWR models
LED
Mark on the panel
Status
Description
Power LED
PWR
ON
The switch is powered on.
OFF
The switch is powered off.
Table 4 Port status LEDs on the Switch 4210 PWR models
Port status
mode LED
mode LED
Port status LED
Description
The A/L LED is
on
on
Yellow LED
(left)
(left)
BLINKING
The port is in the active state and there is
traffic on the port.
traffic on the port.
OFF
The port is in the active state but there is no
traffic on the port.
traffic on the port.
Green LED
(right)
(right)
ON
The port is connected properly.
OFF
The port is not connected or is incorrectly
connected.
connected.
The D/S LED is
on
on
Yellow LED
(left)
(left)
ON
The port operates in the full duplex mode.
OFF
The port operates in the half duplex mode.
Green LED
(right)
(right)
ON
The port rate is 100 Mbps.
OFF
The port rate is 10 Mbps.
Table 5 The 1000 Mbps uplink port status LED on 4210 PWR models
LED
Mark on the
panel Status
panel Status
Description
1000 Mbps uplink port
link LED
link LED
LINK
ON
The port is connected properly.
OFF
The port is not connected or is
incorrectly connected.
incorrectly connected.