Siemens ERTEC200 User Manual
12:10
P2_PHY_MODE
000: 10BASE-T HD, Auto-Neg disabled
001: 10BASE-T FD, Auto-Neg disabled
010: 100BASE-TX/FX HD, Auto-Neg disabled
011: 100BASE-TX/FX FD, Auto-Neg disabled
100: 100BASE-TX HD announced, Auto-Neg enabled
101: 100BASE-TX HD announced, Auto-Neg enabled, Repeater Mode
110: PHY starts in Power Down Mode
111: Auto-Neg enabled, AutoMDIX enabled, everything is possible
001: 10BASE-T FD, Auto-Neg disabled
010: 100BASE-TX/FX HD, Auto-Neg disabled
011: 100BASE-TX/FX FD, Auto-Neg disabled
100: 100BASE-TX HD announced, Auto-Neg enabled
101: 100BASE-TX HD announced, Auto-Neg enabled, Repeater Mode
110: PHY starts in Power Down Mode
111: Auto-Neg enabled, AutoMDIX enabled, everything is possible
9
P2_FX_ MODE
1: The 100BASE-FX Interface is enabled
(only meaningful when P2_PHY_Mode =“010“ or “011“)
0: The 100BASE-FX Interface is disabled
(only meaningful when P2_PHY_Mode =“010“ or “011“)
0: The 100BASE-FX Interface is disabled
8
P2_PHY_ENB
0: PHY2 disabled (Powerdown Mode)
1: PHY2 enabled
7:6
Reserved
5
P1_AUTOMDIXEN
1: Enable AutoMDIX state machine
0: Disable AutoMDIX state machine
0: Disable AutoMDIX state machine
4:2
P1_PHY_ MODE
000: 10BASE-T HD, Auto-Neg disabled
001: 10BASE-T FD, Auto-Neg disabled
010: 100BASE-TX/FX HD, Auto-Neg disabled
011: 100BASE-TX/FX FD, Auto-Neg disabled
100: 100BASE-TX HD announced, Auto-Neg enabled
101: 100BASE-TX HD announced, Auto-Neg enabled, Repeater Mode
110: PHY starts in Power Down Mode
111: Auto-Neg enabled, AutoMDIX enabled, everything is possible
001: 10BASE-T FD, Auto-Neg disabled
010: 100BASE-TX/FX HD, Auto-Neg disabled
011: 100BASE-TX/FX FD, Auto-Neg disabled
100: 100BASE-TX HD announced, Auto-Neg enabled
101: 100BASE-TX HD announced, Auto-Neg enabled, Repeater Mode
110: PHY starts in Power Down Mode
111: Auto-Neg enabled, AutoMDIX enabled, everything is possible
1
P1_FX_ MODE
1: The 100BASE-FX interface is enabled
(only meaningfule when P1_PHY_Mode =“010“ or “011“)
0: The 100BASE-FX interface is disabled
(only meaningfule when P1_PHY_Mode =“010“ or “011“)
0: The 100BASE-FX interface is disabled
0
P1_PHY_ENB
0: PHY1 disabled (Powerdown Mode)
1: PHY1 enabled
PHY_ STATUS
R Addr.:
0x4000_2660
Default: 0x0000_0000
Description
Status of PHY1 and PHY2
Bit No.
Name
Description
31:9
Reserved
8
P2_PWRUPRST
0: PHY2 in Powerdown mode or internal reset is still active
1: PHY2 is ready for operation
1: PHY2 is ready for operation
7:1
Reserved
0 P1_PWRUPRST
0: PHY1 in Powerdown mode or internal reset is still active
1: PHY1 is ready for operation
1: PHY1 is ready for operation
UART_CLK
R/W
Addr.: 0x4000_2670 Default: 0x0000_0000
Description
Enables switching of the UART clock from 50 MHz (default) to 6 MHz. At 6 MHz, a UART baud
rate of 187.5 kBd is possible.
rate of 187.5 kBd is possible.
Bit No.
Name
Description
31:1 Reserved
Reserved
0 UART_TAKT
UART
clock:
0: 50 MHz
1: 6 MHz
1: 6 MHz
2
If the PHY is 'Disabled' and then 'Enabled' again, a Disable Time of > 100
µs must be adhered to by the SW.
3
P1/2_PHYENABLE = 1 triggers a reset extension internally in PHY beyond 5.2 ms. During this time, the PLL and all
analog and digital components are powered up. The ready to operate status is signaled in the PHY_Status-Register with
P1/2_PWRUPRST = 1.
P1/2_PWRUPRST = 1.
Copyright © Siemens AG 2007. All rights reserved.
63
ERTEC 200 Manual
Technical data subject to change Version 1.1.0