Sony MKS-2010 User Manual
Cha
p
te
r 6
Ad
Ad
v
a
nce
d Op
er
a
tio
ns
126
Snapshots
Recalling Snapshots
1
Press the [SNAPSHOT] button, turning it on.
The button lights in amber, and the Flexi Pad control
block enter snapshot operation mode.
Also, the numeric display shows the number of the
bank selected last time, and the number of the register
most recently recalled for the region.
block enter snapshot operation mode.
Also, the numeric display shows the number of the
bank selected last time, and the number of the register
most recently recalled for the region.
2
If the [STORE] button is lit, press the button, turning
it off.
it off.
3
Select the bank to recall.
See steps
4 and 5 of “Saving Snapshots” (page 125).
4
If you want to use a temporary attribute (see page
124), press one of the following buttons, selecting and
lighting it.
124), press one of the following buttons, selecting and
lighting it.
Lit in green: Selected
Lit in orange: Not selected
Lit in orange: Not selected
See page 124 for the attributes which may be used .
Note
The Cross-point hold and Key disable states last until
the [XPT HOLD] or [XP/KY HOLD] button is pressed
again.
the [XPT HOLD] or [XP/KY HOLD] button is pressed
again.
5
Press the memory recall button for the register where
the snapshot that you want is saved (the button is lit in
orange).
the snapshot that you want is saved (the button is lit in
orange).
When the recall is complete, the pressed button lights
in yellow.
The numeric display shows the bank number followed
by the selected register number.
in yellow.
The numeric display shows the bank number followed
by the selected register number.
To maintain cross-point states temporarily with
the bus override function
Recall the snapshot while holding down a cross-point
button in the A or B row on the M/E bank or a cross-point
button in the PGM or PST row on the PGM/PST bank.
The snapshot is recalled without changing the selection of
the signal on the bus. This operation is not necessary when
cross-point hold is on.
the bus override function
Recall the snapshot while holding down a cross-point
button in the A or B row on the M/E bank or a cross-point
button in the PGM or PST row on the PGM/PST bank.
The snapshot is recalled without changing the selection of
the signal on the bus. This operation is not necessary when
cross-point hold is on.
Deleting Snapshots
1
In the Flexi Pad control block, press the [STORE]
button, turning it on.
button, turning it on.
2
While holding down the [SNAPSHOT] button, press
the memory recall button for the snapshot that you
want to delete.
the memory recall button for the snapshot that you
want to delete.
The button goes out after the snapshot is deleted.
M/E and PGM/PST cross-point control blocks, AUX
bus control block
Temporary attribute
Button pressed
Cross-point hold
[XPT HOLD] button in M/E
and PGM/PST cross-point
control blocks
and PGM/PST cross-point
control blocks
Cross-point hold or key
disable for key bus
disable for key bus
[XP/KY HOLD] button in
AUX bus control block
AUX bus control block
Cross-point hold for Aux
bus
bus
Flexi Pad control block
Temporary attribute
Button pressed
Effect dissolve
[EFF DISS] button
2
3
1
4
EFF/
WIPE
SNAP
SHOT
SHOT
PP/
ALL
BANK
SEL
TRANS
RATE
M/E
MCRO
STORE
7
8
9
4
5
6
1
2
3
0
EFF
DISS
AUTO
TRNS
TRNS
Auto transition
[AUTO TRNS] button
Flexi Pad control block
Temporary attribute
Button pressed