Alcatel Carrier Internetworking Solutions 6648 User Manual
Troubleshooting Authenticated VLANs
Dshell Troubleshooting
OmniSwitch Troubleshooting Guide
September 2005
page 18-13
Bit 9: Configuration
- adDebugSetFilterLevel 0xX : Set trace level filter
X = Bit field
Bit 1: ERROR Bit 2: WARNING
Bit 3: INFO
Bit 1: ERROR Bit 2: WARNING
Bit 3: INFO
- adDebugSetFilterPort X : Set user port number filter
Available only for INFO's trace
X = 0 = No filter
X = 0 = No filter
- adDebugShowAvlanIp : Display Authentication IP addresses configured
- adDebugShowContext : Display AD's context
- adDebugShowCounter : Display debug counters
- adDebugShowPort : Display 802.1x port configured
value = 1424 = 0x590
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterLevel 0xff
value = 255 = 0xff
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterFrame 0xffff
value = 65535 = 0xffff
Working: [Kernel]->
AD INFO-> ARP request rcv.on glb.port=0x0,user port=1:Slot=1,Auth.IP
addr.=0x1,Src.MAC known=0x0,Cond.codes=0x16080,Frame=0x63dead8
- adDebugShowContext : Display AD's context
- adDebugShowCounter : Display debug counters
- adDebugShowPort : Display 802.1x port configured
value = 1424 = 0x590
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterLevel 0xff
value = 255 = 0xff
Working: [Kernel]->
Working: [Kernel]->adDebugSetFilterFrame 0xffff
value = 65535 = 0xffff
Working: [Kernel]->
AD INFO-> ARP request rcv.on glb.port=0x0,user port=1:Slot=1,Auth.IP
addr.=0x1,Src.MAC known=0x0,Cond.codes=0x16080,Frame=0x63dead8
AD INFO-> TELNET pkt.rcv.from qDispatcher: Slot=1,Glb.port=0x0,User
port=1,Msg.=0x6b01e98,Cond.codes=0x10080,Frame=0x63dead8
port=1,Msg.=0x6b01e98,Cond.codes=0x10080,Frame=0x63dead8
Notes.
1. The above is not a complete capture of the successful authentication process. A capture of the entire
process would be several pages.
process would be several pages.
2. It is recommended that you run this command only in a test environment and with a specific flat set,
rather than all “ffff” shown in the above example.
rather than all “ffff” shown in the above example.
The Authenticated VLAN adDebugShowContext Function
The adDebugShowContext function displays the following output:
Working: [Kernel]->adDebugShowContext
AD show context
NI Slot = 1
NI Slice = 0
Configuration socket identifier = 286
Packet socket identifier = 287
Authenticated IP addr.configured = Yes
DNS name + 'avlBootpmode' config. = Yes
802.1x node parameters configured = Yes
Default Traffic before authent = No
Port bounding configured = No
avlBootpMode IP address = 172.16.106.5
Configuration socket identifier = 286
Packet socket identifier = 287
Authenticated IP addr.configured = Yes
DNS name + 'avlBootpmode' config. = Yes
802.1x node parameters configured = Yes
Default Traffic before authent = No
Port bounding configured = No
avlBootpMode IP address = 172.16.106.5