Advantech EKI-7657C User Manual
37 Chapter3
systemlog mode
[client|server|both]
G
Specified the log mode
switch(config)# systemlog mode both
show systemlog
E
Displays system log.
Switch>show systemlog
show systemlog
P
Show system log client & server
information
information
switch#show systemlog
no systemlog
G
Disable systemlog functon
switch(config)#no systemlog
smtp enable
G
Enable SMTP function
switch(config)#smtp enable
smtp serverip
[IP address]
G
Configure SMTP server IP
switch(config)#smtp serverip 192.168.1.5
smtp authentication
G
Enable SMTP authentication
switch(config)#smtp authentication
smtp account
[account]
G
Configure authentication account
switch(config)#smtp account User
smtp password
[password]
G
Configure authentication password
switch(config)#smtp password
smtp rcptemail
[Index] [Email address]
G
Configure Rcpt e-mail Address
switch(config)#smtp rcptemail 1
Alert@test.com
show smtp
P
Show the information of SMTP
switch#show smtp
no smtp
G
Disable SMTP function
switch(config)#no smtp
event device-cold-start
[Systemlog|SMTP|Both]
[Systemlog|SMTP|Both]
G
Set cold start event type
switch(config)#event device-cold-start both
event authentication-failure
[Systemlog|SMTP|Both]
G
Set Authentication failure event
type
type
switch(config)#event authentication-failure both
event ring-topology-change
[Systemlog|SMTP|Both]
G
Set X - ring topology changed
event type
event type
switch(config)#event ring-topology-change both
event systemlog
[Link-UP|Link-Down|Both]
I
Set port event for system log
switch(config)#interface fastethernet 3
switch(config-if)#event systemlog both
switch(config-if)#event systemlog both
event smtp
[Link-UP|Link-Down|Both]
I
Set port event for SMTP
switch(config)#interface fastethernet 3
switch(config-if)#event smtp both
switch(config-if)#event smtp both
show event
P
Show event selection
switch#show event
no event device-cold-start
G
Disable cold start event type
switch(config)#no event device-cold-start
no event authentication-failure
G
Disable Authentication failure
event type
event type
switch(config)#no event authentication-failure
no event ring-topology-change
G
Disable X - ring topology changed
event type
event type
switch(config)#no event ring-topology-change
no event systemlog
I
Disable port event for system log
switch(config)#interface fastethernet 3
switch(config-if)#no event systemlog
switch(config-if)#no event systemlog
no event smpt
I
Disable port event for SMTP
switch(config)#interface fastethernet 3
switch(config-if)#no event smtp
switch(config-if)#no event smtp
show systemlog
P
Show system log client & server
information
information
switch#show systemlog
3.1.16
SNTP Commands Set
Table 3.16: SNTP Commands Set
Netstar Commands
Level
Description
Example
sntp enable
G
Enable SNTP function
switch(config)#sntp enable
sntp daylight
G
Enable daylight saving time, if
SNTP function is inactive, this
command can’t be applied.
SNTP function is inactive, this
command can’t be applied.
switch(config)#sntp daylight
sntp daylight-period
[Start time] [End time]
G
Set period of daylight saving time,
if SNTP function is inactive, this
command can’t be applied.
Parameter format:
[yyyymmdd-hh:mm]
if SNTP function is inactive, this
command can’t be applied.
Parameter format:
[yyyymmdd-hh:mm]
switch(config)# sntp daylight-period 20060101-
01:01 20060202-01-01
01:01 20060202-01-01
sntp daylight-offset
[Minute]
G
Set offset of daylight saving time, if
SNTP function is inactive, this
command can’t be applied.
SNTP function is inactive, this
command can’t be applied.
switch(config)#sntp daylight-offset 3
sntp ip
[IP]
G
Set SNTP server IP, if SNTP
function is inactive, this command
can’t be applied.
function is inactive, this command
can’t be applied.
switch(config)#sntp ip 192.169.1.1
sntp timezone
[Timezone]
G
Set timezone index, use “show
sntp timzezone” command to get
more information of index number
sntp timzezone” command to get
more information of index number
switch(config)#sntp timezone 22
show sntp
P
Show SNTP information
switch#show sntp