Adtran Small Form-Factor Pluggable Gigabit Ethernet Leaflet

Page of 2
NOTE: The Gigabit Ethernet port is optical and therefore 
are not classified as any type of port as defined in 
Appendix B of GR-1089-CORE Issue 4.
The SFPGS is designed to meet the following environ-
mental classes:
ETSI EN 300 019-1-1 “Classification of 
environmental conditions; Storage,” Class 1.2
ETSI EN 300 019-1-2 “Classification of 
environmental conditions, Transportation,” Class 2.3
ETSI EN 300 019-1-3 “Classification of 
environmental conditions, Stationary use at weather-
protected locations,” Class 3.3
The equipment is designed to function without degra-
dation during exposure to all test severities per Class 3.3.
The Small Form-Factor Pluggable Gigabit Ethernet 
www.adtran.com
 for 
further information on RoHS/WEEE.
COMPLIANCE
CAUTION: Electrostatic Discharge (ESD) can damage 
electronic modules. When handling modules, 
wear an antistatic discharge wrist strap to 
prevent damage to electronic components. Place 
modules in antistatic packing material when 
transporting or storing. When working on 
modules, always place them on an approved 
antistatic mat that is electrically grounded.
The SFPGS is NRTL Listed to the applicable UL 
standards. The SFPGS meets or exceeds all the 
applicable requirements of NEBS, Telcordia
 
GR-63-CORE, and GR-1089-CORE. The SFPGS 
is intended for deployment in Central Office type 
facilities, EEEs, EECs, and locations where the 
NEC applies (for example, Customer Premises). 
Install the SFPGS in an ADTRAN product located 
in a restricted access location.
This device complies with Part 15 of the FCC rules. 
Operation is subject to the following two conditions:
1. This device may not cause harmful interference
2. This device must accept any interference received, 
including interference that may cause undesired 
operation.
Changes or modifications not expressly approved by 
ADTRAN could void the user's authority to operate this 
equipment.
CAUTION: Per GR-1089-CORE the ADTRAN system that 
the SFP is being deployed in is designed and 
intended for installation as part of a Common 
Bonding Network (CBN). The ADTRAN system 
that the SFP is being deployed in is not designed 
nor intended for installation as part of an 
Isolated Bonding Network (IBN).
Per GR-1089-CORE Section 9, the SFPGS does 
not have an internal DC connection between 
battery return and frame ground. The SFPGS 
can be installed in a DC-I (isolated) or DC-C 
(common) installation. For installations where 
other cards or the host system have internal 
connections between battery return and frame 
ground, the system would be intended for 
deployment only in a DC-C installation.
The ADTRAN system chassis frame ground 
terminal must be connected to an earth ground to 
ensure that the metal enclosure of the SFPGS is 
properly grounded via the backplane connector.
Warranty
: ADTRAN will replace or repair this product within the warranty period if it does not meet 
its published specifications or fails while in service. Warranty information can be found 
online at 
www.adtran.com/warranty
.
© 2008 ADTRAN, Inc. All Rights Reserved.
*61184561PG1-22A*
C A U T I O N ! 
SUBJECT TO ELECTROSTATIC DAMAGE
OR DECREASE IN RELIABILITY.
HANDLING PRECAUTIONS REQUIRED.
CLEI: SOOTAD9J_ _
Product P/N: 1184561PG1
Issue Date: 0804
Document P/N: 61184561PG1-22A
PRICING AND AVAILABILITY
800.827.0807
TECHNICAL SUPPORT
800.726.8663
RETURN FOR REPAIR
256.963.8722
Small Form-Factor Pluggable
Gigabit Ethernet, Single-Mode