Liebert 100-1000A User Manual

A

B

TOP VIEW

FRONT VIEW

BOTTOM VIEW

ISOMETRIC VIEW 

36.9"

83.9"

SEE HEIGHT

TABLE

29.44"

TYP.

2.47"

TYP.

71.55"

TYP.

2.47"

TYP

MOUNTING

PLATE

ALIGN FOOT PARALLEL 

TO MOUNTING PLATE AS 

SHOWN

FOOT DETAIL A

FOOT DETAIL B

RIGHT SIDE VIEW

INSTALLATION NOTES:

1. CHECK ALL HARDWARE FOR PROPER TORQUE PRIOR TO INSTALLATION.

2. INSTALL REAR LOWER STS2 BRACKET TO THE FLOOR STAND USING EXISTING HOLES WITH 

    BENT FLANGE FACING THE FRONT OF THE FLOOR STAND (FIG. 3 AND FIG 4, DWG PS217001). 

    USE M12-1.75X40mm CAP SCREW, SPLIT LOCK WASHER, AND FLAT WASHER AND TORQUE TO 53 FT-LBS. 

3. LOOSEN THE STS2 ADJUSTABLE LEVELER FEET NUTS (SEE DETAIL C; DWG PS217001). INSTALL REAR 

    UPPER STS2 BRACKET USING EXISTING HOLES ON UNDERSIDE OF THE STS2 WITH TABS FACING OUT 

    (FIG 1 AND FIG 2, PS217001). INSTALL FRONT UPPER STS2 BRACKET USING EXISTING HOLES ON 

    UNDERSIDE OF THE STS2 WITH BENT FLANGE FACING TO THE FRONT. (FIG.1 AND FIG 2, PS217001). 

    USE M12-1.75X40mm 

CAP SCREW, SPLIT LOCK WASHER, AND FLAT WASHER AND TORQUE TO

    53 FT-LBS. RETIGHTEN LEVELER FEET NUTS. 

4. FLOOR STAND CAN BE MOUNTED NEXT TO A WALL IF NEEDED, REAR ACCESS NOT REQUIRED. 

    INSTALL FLOOR STAND WITH FEET ORIENTATED AS SHOWN IN (BOTTOM VIEW; DWG PS217000). 

    TO ADJUST VERTICAL HEIGHT OF FLOOR STAND FEET, LOOSEN, ADJUST AND TIGHTEN THE NUTS 

    AND 

JAM NUT SHOWN IN (FOOT DETAIL A & B; ON DWG PS217000). FLOOR STAND MUST BE LEVEL 

    AND 

ALL FEET MUST BE TOUCHING THE FLOOR. ATTACH FLOOR STAND FEET USING 1/2" X 4" RED HEAD 

    T

R

U

BOLTS EXPANSION ANCHORS (FEILD SUPPLIED) (2) PER FOOT.

5. ROLL THE STS2 ONTO THE FLOOR STAND SO THAT THE TABS ON THE (REAR UPPER STS2 BRACKET) 

    FIT 

INTO THE SLOTS ON THE (REAR LOWER STS2 BRACKET). TABS TO EXTEND AT LEAST 1/2" THROUGH 

    FLOOR 

STAND BRACKET (FIG. 2, DWG PS217002). 

6. INSTALL 

THE LOWER FRONT BRACKETS (FIG 1, DETAIL A; DWG PS217002). ATTACH BRACKET TO STS2 

    USING 

M10-1.50X30mm CAP SCREW, SPLIT LOCK WASHER, AND FLAT WASHER AND TORQUE TO 

    31 FT-LBS. 

ATTACH BRACKET TO FLOOR STAND USING M12-1.75X40mm CAP SCREW, SPLIT LOCK WASHER, 

    AND 

FLAT WASHER AND TORQUE TO 53 FT-LBS

NUT

JAM NUT

NUT

HEIGHT TABLE

P/N OF FLOOR 

STAND:

H

E

IG

H

T

HEIGHT MAX:

H

EIGHT MIN:

523409G1

1

8

.0

"

1

9

.2

5

"

1

6

.7

5

"

523410G1

2

4

.0

"

2

5

.2

5

"

2

2

.7

5

"

523411G1

3

0

.0

"

3

1

.2

5

"

2

8

.7

5

"

523412G1

36.0"

3

7.25"

3

4.75"

6" TYP.

HARDWARE TORQUE 

CHART

1.0" NUT

320 FT - LBS

M8 - 1.25

16FT - LBS

M10 

- 

1.5

31 FT - LBS

M12 - 1.75

5

3

 F

T

 -

L

B

S

PS217000 Rev

. 0