Liebert 1000A User Manual

5. 

MOVE 

CABINET 

INTO

 P

OSITION

 W

ITH 

REAR 

TABS 

INTO

 S

LOTS 

OF

FLOOR BRACKET. TABS TO EXTEND AT LEAST 1/2" THROUGH FLOOR

BRACKET 

(FIG. 

2). 

THEN 

ATTACH 

FRONT FLOOR BRACKETS 

TO 

FRONT

CABINET 

BASE 

BRACKET 

BUT 

DO

 N

OT 

FULLY

 T

IGHTEN 

HARDWARE.

6. 

MARK 

HOLE LOCATIONS AND REMOVE BRACKETS. DRILL AND INSTALL

FLOOR 

BRACKETS. 

UNIT 

DOOR 

CAN BE 

REMOVED 

FOR BETTER 

ACCESS.

REINSTALL 

FRONT FLOOR BRACKETS 

TO 

FRONT CABINET 

BRACKETS 

WITH

SUPPLIED HARDWARE AND TORQUE TO 235 LB-IN (26.5 Nm), (FIG. 3).

7.

 IF

 SIDE 

WALLS 

ARE 

PRESENT, 

5.0

 INCH 

MINIMUM

 D

ISTANCE 

FROM 

EITHER

SIDE WALL 

IS 

REQUIRED. 

8. REAR

 A

ND 

FRONT 

FLOOR 

BRACKETS, 

AND 

REAR 

AND 

FRONT 

CABINE

T

BASE BRACKETS 

ARE 

1010 

STEEL 

AND 

APPROX. 

.25 

INCH 

THICK.

NOTES:

1. RECOMMENDED 

FLOOR 

ANCHOR: 

1/2" 

ITW 

RAMSET/RED 

HEAD

SELF DRILLING 

ANCHOR, 

ICBO 

#ER-1372 

OR 

EQUIVALENT 

(NOT

(SUPPLIED). FOLLOW MANUFACTURER'S INSTRUCTIONS.

2. POSITION 

REAR 

FLOOR 

BRACKETS 

ON 

FLOOR 

AT 

LEAST 

.75" 

FROM 

BACK WALL. 

MARK 

LOCATION

 A

ND 

DRILL 

HOLES 

(FIG. 

1) 

TO

A MINIMUM DEPTH OF 4.12" INTO THE CONCRETE. 

3. INSTALL 

REAR 

CABINET 

BASE 

BRACKET 

(FIG. 

2) 

TO 

EXISTING 

HOLES ON UNDERSIDE OF UNIT WITH TABS FACING BACK WALL. 

USE SUPPLIED HARDWARE AND TORQUE TO 365 LB-INCH (41.2 Nm). NOTE, LOOSEN 

LEVELING 

BOLT 

LOCKING 

NUT 

AND 

TIGHTEN 

AFTER

BRACKET IS 

SECURED. 

4. INSTALL 

FRONT 

CABINET 

BASE 

BRACKET 

(FIG. 

3) 

TO 

EXISTING 

HOLES 

ON

 U

NDERSIDE 

OF 

UNIT WITH BENT FLANGE FACING FRONT.

USE SUPPLIED HARDWARE AND TORQUE TO 365 LB-INCH (41.2 Nm).

NOTE, LOOSEN 

LEVELING 

BOLT 

LOCKING 

NUT 

AND 

TIGHTEN 

AFTER 

BRACKET IS 

SECURED.

SYSTEM SEISMIC ANCHORING, 

FIGURE 

1

TOP VIEW

32.

2"

(817

 MM)

FRONT

13

.2"

(335 MM)

13

.2"

15

.6"

(335 MM)

(39

6 M

M)

(310

 M

M)

12

.2"

13

.2"

(335 MM

)

13

.2"

(335 MM)

(107

 MM) 4.2"

(107

 MM) 4.2"

11.4

"

(289 M

M)

(107

 M

M)

4.2"

4.2"

(107

 M

M)

(144 M

M)

5.7

"

32.

75

"

(832 MM)

SEE NOTE 

(7)

FOR SPACING

BACK WALL

REAR FLOOR  BRACKET SEE NOTE 

(2)

FOR SPACING

FRONT FLOOR  BRACKET

SIDE WALL

PS211805 Rev. 0

FLOOR ANCHOR HARDWARE (NOT SUPPLIED

)

FIGURE 2

REAR CABINET BASE BRACKET

FLOOR LINE

BRACKET

REAR F

LOOR

 

APPROX 1/2"

BACK WALL

FRONT CABINET  BASE BRACKET

FIGURE 3

BRACKET

FLOOR ANCHOR HARDWARE NOT SUPPLIED

FRONT FLOOR

FRONT DOOR OF CABINET

HARDWARE SUPPLIED

FLOOR LINE