Honeywell 1450g User Manual

Page of 206
Voyager™ 1450g/1452g Series
Area-Imaging Scanner
User’s Guide

Summary of Contents of user manual for Honeywell 1450g

  • Page 1Voyager™ 1450g/1452g Series Area-Imaging Scanner User’s Guide
  • Page 2Disclaimer Honeywell International Inc. (“HII”) reserves the right to make changes in specifications and other information contained in this document...
  • Page 3 Table of Contents Chapter 1 - Getting Started About This Manual ...............................................................................................................1-1 Unpacking Your Device .......................................................................................................1-1 Connecting the Device...
  • Page 4 RS232 Modifiers ................................................................................................................ 2-18 RS232 Baud Rate........................................................................................................ 2-18 RS232 Word Length: Data Bits, Stop Bits, and Parity ................................................. 2-19...
  • Page 5 Scanner Modes ................................................................................................................... 3-9 Charge Only Mode......................................................................................................... 3-9 Linked Modes ................................................................................................................ 3-9 Unlinking the Scanner ....................................................................................................... 3-10 Override Locked...
  • Page 6 Good Read and Error Indicators.......................................................................................... 4-2 Beeper – Good Read..................................................................................................... 4-2 Beeper Volume – Good Read........................................................................................ 4-2 Beeper Pitch...
  • Page 7Chapter 5 - Data Editing Prefix/Suffix Overview ......................................................................................................... 5-1 To Add a Prefix or Suffix:............................................................................................... 5-1 To Clear One or...
  • Page 8 GS1-128 ............................................................................................................................ 7-17 UPC-A ............................................................................................................................... 7-17 UPC-A/EAN-13 with Extended Coupon Code ................................................................... 7-19 Coupon GS1 DataBar Output............................................................................................ 7-20 UPC-E0...
  • Page 9 Show Data Format............................................................................................................... 9-1 Test Menu............................................................................................................................ 9-2 EZConfig-Scanning Introduction.......................................................................................... 9-2 Installing EZConfig-Scanning from the Web.................................................................. 9-2 Resetting the Factory...
  • Page 10Appendix A - Reference Charts Symbology Charts ...............................................................................................................A-1 Linear Symbologies .......................................................................................................A-1 2D Symbologies.............................................................................................................A-2 Postal Symbologies .......................................................................................................A-2 ASCII Conversion Chart (Code...
  • Page 111 Getting Started About This Manual This User’s Guide provides installation and programming instructions for the Voyager™ 1450g corded area-imaging...
  • Page 12 CCB01-010BT Base USB Connection: Note: The power supply must be ordered separately, if needed. 2. If you are connecting...
  • Page 13 CCB01-010BT Base Keyboard Wedge Connection: Note: The power supply must be ordered separately, if needed. 3. If you are...
  • Page 14 Corded Voyager 1450g RS232 Serial Port Connection: CCB01-010BT Base RS232 Serial Port Connection: Note: The power supply must be...
  • Page 15 Corded Voyager 1450g RS232 Serial Port Connection: CCB01-010BT Base RS485 Connection: 2. Turn the terminal/computer power back on. The...
  • Page 16Mounting a CCB01-010BT Charge Base 2.8 in. 2.36 in. 72.1mm 59.84mm 3.35 in. 8x32 thread 85.09mm x .39 in. (10mm)...
  • Page 17Setting Custom Defaults You have the ability to create a set of menu commands as your own, custom defaults. To...
  • Page 181-8
  • Page 192 Programming the Interface Introduction This chapter describes how to program your system for the desired interface. Programming the Interface...
  • Page 20RS485 Scan one of the following “Plug and Play” codes to program the scanner for an IBM POS terminal interface....
  • Page 21 RS485 Packet Length If you are using Packet mode, you can specify the size of the data “packet” that...
  • Page 22USB HID Scan the following code to program the scanner for USB HID bar code scanners. USB HID Bar Code...
  • Page 23Remote MasterMind™ for USB When using a USB interface, you may wish to configure your scanner to communicate with Remote...
  • Page 24Honeywell Bioptic Aux Port Configuration Scan the following Plug and Play code to program the scanner for a Honeywell bioptic...
  • Page 25Wincor Nixdorf Beetle™ Terminal Default Settings Scan the following Plug and Play code to program the scanner for a Wincor...
  • Page 26Keyboard Country Layout Scan the appropriate country code below to program the keyboard layout for your country or language. As...
  • Page 27Keyboard Countries (Continued) Bulgaria (Latin) Canada (French legacy) Canada (French) Canada (Multilingual) Croatia Czech Czech (Programmers) Czech (QWERTY) Czech (QWERTZ)...
  • Page 28 Keyboard Countries (Continued) Estonia Faroese Finland France Gaelic Germany Greek Greek (220 Latin) Greek (220) Greek (319 Latin) Greek...
  • Page 29Keyboard Countries (Continued) Greek (Latin) Greek (MS) Greek (Polytonic) Hebrew Hungarian (101 key) Hungary Iceland Irish Italian (142) Italy Japan...
  • Page 30 Keyboard Countries (Continued) Kazakh Kyrgyz (Cyrillic) Latin America Latvia Latvia (QWERTY) Lithuania Lithuania (IBM) Macedonia Malta Mongolian (Cyrillic) Norway...
  • Page 31Keyboard Countries (Continued) Poland Polish (214) Polish (Programmers) Portugal Romania Russia Russian (MS) Russian (Typewriter) SCS Serbia (Cyrillic) Serbia (Latin)...
  • Page 32 Keyboard Countries (Continued) Slovakia Slovakia (QWERTY) Slovakia (QWERTZ) Slovenia Spain Spanish variation Sweden Switzerland (French) Switzerland (German) Tatar Turkey...
  • Page 33 Keyboard Countries (Continued) Turkey Q Ukrainian United Kingdom United States (Dvorak) United States (Dvorak left) United Stated (Dvorak right)...
  • Page 34Shift Lock is used when you normally have the Shift Lock key on (not common to U.S. keyboards). Shift Lock...
  • Page 35Control Character Output This selection sends a text string instead of a control character. For example, when the control character...
  • Page 36Turbo Mode: The scanner sends characters to a terminal faster. If the terminal drops characters, do not use Turbo Mode....
  • Page 37 1200 2400 4800 * 9600 19200 38400 57,600 115,200 RS232 Word Length: Data Bits, Stop Bits, and Parity Data...
  • Page 38 7 Data, 1 Stop, Parity None 7 Data, 1 Stop, Parity Odd 7 Data, 2 Stop, Parity Even 7...
  • Page 39Two-Direction Flow Control: The scanner asserts RTS when it is OK for the host to transmit. The host asserts CTS...
  • Page 40 ACK/NAK After transmitting data, the scanner waits for an ACK character (hex 06) or a NAK character (hex 15)...
  • Page 41Scanner-Bioptic ACK/NAK Timeout This allows you to set the length (in milliseconds) for a timeout for a bioptic scanner’s ACK/NAK...
  • Page 422 - 24
  • Page 433 Cordless System Operation Note: This chapter applies only to cordless scanning systems. It does not apply to corded scanners....
  • Page 44Scan the linking bar code on the top of the Access Point to establish a connection between the Access Point...
  • Page 45Programming the Scanner and Base or Access Point When using the scanner and charge base or Access Point together as...
  • Page 46About the Battery There is a danger of explosion if the batteries are incorrectly replaced. Replace the batteries with only...
  • Page 47Beeper and LED Sequences and Meaning The scanner contains LEDs on the rear of the unit that indicate linking status,...
  • Page 48 Base Power Communication Indicator Off Reset Scanner Scanning this bar code reboots the scanner and causes it to relink...
  • Page 49Default = External or Interface Cable Power. Base Charge Off External or Interface Cable Power External Power Only Paging Paging...
  • Page 50 High (4200 Hz) Error Indicators Beeper Pitch - Base Error The CCB01-010BT base can be configured to beep at...
  • Page 51Scanner Address Scan the bar code below to determine the address of the scanner you are using. Scanner Address Base...
  • Page 52 Locked Link Mode - Single Scanner If you link a scanner to a base or an Access Point using...
  • Page 53options for the scanner or the base and to set the alarm duration, scan the appropriate bar code below and...
  • Page 54If there are no trigger pulls during the timer interval, the scanner goes into power down mode. Whenever the trigger...
  • Page 55Scan one of the bar codes below to set the scanner’s power output to Full Power (100%), Medium Power (35%),...
  • Page 56 Inventory Batch Mode Persistent Batch Mode Batch Mode Beep When scanning in Inventory Batch Mode (page 3-14), the scanner...
  • Page 57Batch Mode Quantity When in Batch Mode, you may wish to transmit the number of multiple bar codes scanned, rather...
  • Page 58 1 2 3 4 5 6 7 8 9 Batch Mode Output Order When batch data is transmitted, select...
  • Page 59Total Records If you wish to output the total number of bar codes scanned when in Batch Mode, scan Total...
  • Page 60 Batch Mode Transmit Delay Medium (500 ms) Batch Mode Transmit Delay Long (1000 ms) Multiple Scanner Operation Note: Multiple...
  • Page 61 0004 0005 0006 0007 Reset You may also scan the Scanner Name bar code below and scan a number...
  • Page 62 Application Work Group Selection This programming selection allows you to assign a scanner to a work group by scanning...
  • Page 63Resetting the Custom Defaults: All Application Work Groups If you want the custom default settings restored to all of the...
  • Page 64 2 3 4 5 6 7 8 9 Save Virtual Keyboard Once your scanner has been connected directly to...
  • Page 65 Bluetooth HID Keyboard Disconnect If your scanner has been connected directly to an iPad, smart phone, or laptop using...
  • Page 66 Auto Reconnect Mode Auto Reconnect controls whether or not the scanner automatically begins the relink process when a loss...
  • Page 67Scan the Maximum Link Attempts bar code, then scan the number of attempts for the setting (from 0-100) from the...
  • Page 68Host Acknowledgment Some applications require that the host terminal (or server) validate incoming bar code data (database look-up) and provide...
  • Page 69Host ACK On/Off Host ACK On * Host ACK Off Host ACK Responses Command Action [ESC] a, Double beeps to...
  • Page 703 - 28
  • Page 714 Input/Output Settings Power Up Beeper The scanner can be programmed to beep when it’s powered up. If you are...
  • Page 72 Trigger Click On Good Read and Error Indicators Beeper – Good Read The beeper may be programmed On or...
  • Page 73 * Medium (2400 Hz) High (4200 Hz) Beeper Pitch – Error The beeper pitch codes modify the pitch (frequency)...
  • Page 74 Number of Beeps – Good Read The number of beeps of a good read can be programmed from 1...
  • Page 75Manual Trigger Mode When in manual trigger mode, the scanner scans until a bar code is read, or until the...
  • Page 76Presentation Mode Presentation Mode uses ambient light to detect bar codes. The LED dims until a bar code is presented...
  • Page 77In the example below, the white box is the centering window. The centering window has been set to 20% left,...
  • Page 78 Left of Presentation Centering Window Right of Presentation Centering Window In-Stand Sensor Mode This feature senses when the scanner...
  • Page 79 Poor Quality PDF Codes This setting improves the scanner’s ability to read damaged or badly printed PDF codes by...
  • Page 80Scan the Hands Free Time-Out bar code, then scan the time-out duration (from 0-300,000 milliseconds) from the inside back cover,...
  • Page 81 Short (1000ms) Medium (2000ms) Long (3000ms) Extra Long (4000ms) Character Activation Mode You may use a character sent from...
  • Page 82 End Character Activation After Good Read After a bar code is successfully detected and read from the scanner, the...
  • Page 83Illumination Lights If you want the illumination lights on while reading a bar code, scan the Lights On bar code,...
  • Page 84 * Interlaced Centering Use Centering to narrow the scanner’s field of view to make sure that when the scanner...
  • Page 85 * Centering Off Top of Centering Window Bottom of Centering Window Left of Centering Window Right of Centering Window...
  • Page 86Video Reverse Video Reverse is used to allow the scanner to read bar codes that are inverted. The Video Reverse...
  • Page 87 * Upright Vertical, Bottom to Top Upside Down Vertical, Top to Bottom 4 - 17
  • Page 884 - 18
  • Page 895 Data Editing Prefix/Suffix Overview When a bar code is scanned, additional information is sent to the host computer along...
  • Page 90 Example: Add a Tab Suffix to All Symbologies Step 1. Scan Add Suffix. Step 2. Scan 9, 9 from...
  • Page 91 Clear One Suffix Clear All Suffixes Function Code Transmit When this selection is enabled and function codes are contained...
  • Page 92 Next, scan the Character to Trigger Delay bar code, then the 2-digit hex value for a printable character to...
  • Page 936 Data Formatting Data Format Editor Introduction You may use the Data Format Editor to change the scanner’s output. For...
  • Page 94 from the Programming Chart inside the back cover of this manual. (Note: 50 characters is entered as 0050. 9999...
  • Page 95 Terminal ID Table Terminal Model(s) Terminal ID USB PC keyboard (HID) 124 Mac Keyboard 125 PC Keyboard (Japanese) 134...
  • Page 96 The data is output as: 1234567890 ABCDEFGHIJ <CR> Send all characters up to a particular character F3 Include in...
  • Page 97 F5 Example: Move the cursor forward and send the data Move the cursor forward 3 characters, then send the...
  • Page 98 F8 Example: Send bar code data that starts after a particular character Search for the letter “D” in bar...
  • Page 99Miscellaneous Commands Suppress characters FB Suppress all occurrences of up to 15 different characters, starting at the current cursor position,...
  • Page 100 The data is output as: 1234 5678 ABC <CR> Stop replacing characters E5 Terminates character replacement. Syntax = E5....
  • Page 101 Insert a delay EF Inserts a delay of up to 49,995 milliseconds (in multiples of 5), starting from the...
  • Page 102 Data Format 3 6 - 10
  • Page 1037 Symbologies This programming section contains the following menu selections. Refer to Chapter 10 for settings and defaults. • All...
  • Page 104EXAMPLE: Decode only those bar codes with a count of 15 characters. Min. length = 15Max. length = 15 For...
  • Page 105 Validate Modulo 16, but Don’t Transmit Validate Modulo 16 and Transmit Codabar Concatenation Codabar supports symbol concatenation. When you...
  • Page 106Code 39 < Default All Code 39 Settings > Code 39 On/Off * On Off Code 39 Start/Stop Characters Start/Stop...
  • Page 107Code 39 Message Length Scan the bar codes below to change the message length. Refer to Message Length Description (page...
  • Page 108 Full ASCII If Full ASCII Code 39 decoding is enabled, certain character pairs within the bar code symbol will...
  • Page 109Interleaved 2 of 5 < Default All Interleaved 2 of 5 Settings > Interleaved 2 of 5 On/Off * On...
  • Page 110 Maximum Message Length NEC 2 of 5 < Default All NEC 2 of 5 Settings > NEC 2 of...
  • Page 111 NEC 2 of 5 Message Length Scan the bar codes below to change the message length. Refer to Message...
  • Page 112 Code 93 Append This function allows the scanner to append the data from several Code 93 bar codes together...
  • Page 113Straight 2 of 5 Industrial (three-bar start/stop) <Default All Straight 2 of 5 Industrial Settings> Straight 2 of 5 Industrial...
  • Page 114Straight 2 of 5 IATA (two-bar start/stop) <Default All Straight 2 of 5 IATA Settings> Straight 2 of 5 IATA...
  • Page 115Matrix 2 of 5 <Default All Matrix 2 of 5 Settings> Matrix 2 of 5 On/Off On * Off Matrix...
  • Page 116Code 11 <Default All Code 11 Settings> Code 11 On/Off On * Off Check Digits Required This option sets whether...
  • Page 117Code 128 <Default All Code 128 Settings> Code 128 On/Off * On Off ISBT 128 Concatenation In 1994 the International...
  • Page 118 Code 128 Append This function allows the scanner to append the data from several Code 128 bar codes together...
  • Page 119GS1-128 <Default All GS1-128 Settings> GS1-128 On/Off * On Off GS1-128 Message Length Scan the bar codes below to change...
  • Page 120 UPC-A Check Digit This selection allows you to specify whether the check digit should be transmitted at the end...
  • Page 121 UPC-A Addenda Required When Required is scanned, the scanner will only read UPC-A bar codes that have addenda. You...
  • Page 122Coupon GS1 DataBar Output If you scan coupons that have both UPC and GS1 DataBar codes, you may wish to...
  • Page 123UPC-E0 Addenda Required When Required is scanned, the scanner will only read UPC-E bar codes that have addenda. Default =...
  • Page 124 UPC-E0 Addenda This selection adds 2 or 5 digits to the end of all scanned UPC-E data. Default =...
  • Page 125EAN/JAN-13 <Default All EAN/JAN Settings> EAN/JAN-13 On/Off * On Off Convert UPC-A to EAN-13 When UPC-A Converted to EAN-13 is...
  • Page 126 EAN/JAN-13 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-13 data. Default =...
  • Page 127 ISBN Translate When On is scanned, EAN-13 Bookland symbols are translated into their equivalent ISBN number format. Default =...
  • Page 128 EAN/JAN-8 Addenda This selection adds 2 or 5 digits to the end of all scanned EAN/JAN-8 data. Default =...
  • Page 129MSI <Default All MSI Settings> MSI On/Off On * Off MSI Check Character Different types of check characters are used...
  • Page 130 Validate Type 11 then Type 10 Character and Transmit Disable MSI Check Characters MSI Message Length Scan the bar...
  • Page 131GS1 DataBar Omnidirectional < Default All GS1 DataBar Omnidirectional Settings > GS1 DataBar Omnidirectional On/Off * On Off GS1 DataBar...
  • Page 132GS1 DataBar Expanded < Default All GS1 DataBar Expanded Settings > GS1 DataBar Expanded On/Off * On Off GS1 DataBar...
  • Page 133 Codablock A Message Length Scan the bar codes below to change the message length. Refer to Message Length Description...
  • Page 134PDF417 < Default All PDF417 Settings > PDF417 On/Off * On Off PDF417 Message Length Scan the bar codes below...
  • Page 135MicroPDF417 < Default All MicroPDF417 Settings > MicroPDF417 On/Off On * Off MicroPDF417 Message Length Scan the bar codes below...
  • Page 136 UPC/EAN Version Scan the UPC/EAN Version On bar code to decode GS1 Composite symbols that have a U.P.C. or...
  • Page 137 GS1 DataBar Emulation GS1 Code Expansion Off EAN8 to EAN13 Conversion * GS1 Emulation Off TCIF Linked Code 39...
  • Page 138 QR Code Message Length Scan the bar codes below to change the message length. Refer to Message Length Description...
  • Page 139Data Matrix < Default All Data Matrix Settings > Data Matrix On/Off * On Off Data Matrix Message Length Scan...
  • Page 140 codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save...
  • Page 141Aztec Code < Default All Aztec Code Settings > Aztec Code On/Off * On Off Aztec Code Message Length Scan...
  • Page 142 codes were created (see ISO 2022/ISO 646 Character Replacements on page A-7), and scan the value and the Save...
  • Page 143Postal Codes - 2D The following lists the possible 2D postal codes, and 2D postal code combinations that are allowed....
  • Page 144 Postnet On Also see Postnet Check Digit, page 7-44. Postnet with B and B’ Fields On InfoMail On Combination...
  • Page 145 Planet Code and Postnet with B and B’ Fields On Planet Code and Postal-4i On Planet Code and Intelligent...
  • Page 146 Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet On Planet Code, Postal-4i, Intelligent Mail Bar Code, and Postnet...
  • Page 147 Combination C and N Tables causes the field to be interpreted using either the C or N Tables. *...
  • Page 148 Maximum Message Length Korea Post <Default All Korea Post Settings> Korea Post On * Off Korea Post Message Length...
  • Page 1498 Interface Keys Keyboard Function Relationships The following Keyboard Function Code, Hex/ASCII Value, and Full ASCII “CTRL”+ relationships apply to...
  • Page 150Country Codes Denmark 8 \ 9 6 - Norway 8 \ 9 6 - Spain [ \ ] 6 -...
  • Page 1519 Utilities To Add a Test Code I.D. Prefix to All Symbologies This selection allows you to turn on transmission...
  • Page 152Test Menu When you scan the Test Menu On code, then scan a programming code in this manual, the scanner...
  • Page 153 5. When prompted, select Save File, and save the files to the c:\windows\temp directory. 6. Once you have finished...
  • Page 1549-4
  • Page 15510 Serial Programming Commands The serial programming commands can be used in place of the programming bar codes. Both the...
  • Page 156 SubTag Field Usage When a query is used in place of a SubTag field, the query applies only to...
  • Page 157This response indicates that the device’s Codabar Coding Enable (CBRENA) is set to 1, or on; the Start/Stop Character (SSX)...
  • Page 158 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry IBM Port 9B HHBCR-2 Interface PAP9B2...
  • Page 159 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Czech (QWERTY) KBDCTY39 2-9 Czech (QWERTZ)...
  • Page 160 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Russian (MS) KBDCTY67 2-13 Russian (Typewriter)...
  • Page 161 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Turbo Mode On KBDTMD1 2-18 *Numeric...
  • Page 162 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Cordless System Operation Note: This section...
  • Page 163 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Flexible Power Management *Full Power BT_TXP100...
  • Page 164 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Resetting the Custom Defaults: All Custom...
  • Page 165 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Good Read Delay *No Delay DLYGRD0...
  • Page 166 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry 2D Reread Delay *2D Reread Delay...
  • Page 167 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Clear One Prefix PRECL2 5-2 Clear...
  • Page 168 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry On CBRCCT1 7-3 Require CBRCCT2 7-3...
  • Page 169 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Validate, But Don’t N25CK21 7-8 Transmit...
  • Page 170 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Off 128ENA0 7-15 *On 128ENA1 7-15...
  • Page 171 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry UPC-E0 Addenda Separator *On UPEADS1 7-21...
  • Page 172 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry MSI Default All MSI Settings MSIDFT...
  • Page 173 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry *On PDFENA1 7-32 Off PDFENA0 7-32...
  • Page 174 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry MaxiCode Msg. Length Minimum (1-150) *1...
  • Page 175 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Postnet with B and B’ Fields...
  • Page 176 Setting Serial Command Selection Page * Indicates default # Indicates a numeric entry Resetting the Factory Defaults Remove Custom...
  • Page 17711 Product Specifications Voyager 1450g Scanner Product Specifications Parameter Specification Mechanical Height 3.23 in. (82mm) Length 2.45 in. (62mm) Width...
  • Page 178Voyager 1452g Cordless Scanner Product Specifications Parameter Specification Mechanical Height 6.8 in. (17.3cm) Length 3.2 in. (8.2cm) Width 2.5 in....
  • Page 179 Parameter Specification 20 mil Code 39 45 - 300mm (1.8 - 11.8 in.) 6.7 mil PDF417 45 - 100mm (1.8...
  • Page 180Standard Cable Pinouts Note: The following pin assignments are not compatible with Honeywell legacy products. Use of a cable with...
  • Page 181RS485 Output 10 Pin RJ41 Modular Plug Note: RS485 signal conversion is performed in the cable. 1 Cable shield 2...
  • Page 182Required Safety Labels Voyager 1450g/1452g Scanner Laser Output Part Number, Laser Safety Serial Number information Laser Label, and Revision Information...
  • Page 183 CCB01-010BT Base Part Number, Serial Number and Compliance Revision Label Information locations location 11 - 7
  • Page 18411 - 8
  • Page 18512 Maintenance Repairs Repairs and/or upgrades are not to be performed on this product. These services are to be performed...
  • Page 186 Replacing a Corded Scanner Interface Cable 1. Turn the power to the host system OFF. 2. Disconnect the scanner’s...
  • Page 187 Changing a Cordless Scanner Battery 1. Use the hinged wire or a flat head screwdriver to remove the screw...
  • Page 188 If your base is not functioning properly, review the following troubleshooting guidelines to try to isolate the problem. Is...
  • Page 18913 Customer Support Technical Assistance If you need assistance installing or troubleshooting your device, please contact us by using one...
  • Page 190EVEN WHEN HII MAY HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH INJURIES, LOSSES, OR DAMAGES. SOME STATES, PROVINCES, OR...
  • Page 191A Reference Charts Symbology Charts Note: “m” represents the AIM modifier character. Refer to International Technical Specification, Symbology Identifiers, for...
  • Page 192 AIM Honeywell Possible modifiers Symbology ID ID Hex (m) UPC-A with Add-On ]E3 c 63 UPC-A with Extended Coupon...
  • Page 193 AIM Honeywell Possible modifiers Symbology ID ID Hex (m) Canadian Post ]X0 C 43 China Post ]X0 Q 51...
  • Page 194Non-printable ASCII control Keyboard Control + ASCII (CTRL+X) Mode characters Windows Mode Control + X Mode On (KBDCAS2) DEC HEX...
  • Page 195 Extended ASCII Characters DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 128 80 € Ç up arrow...
  • Page 196 Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 179 B3 ³ │ 180...
  • Page 197 Extended ASCII Characters (Continued) DEC HEX CP 1252 ASCII Alternate Extended PS2 Scan Code 231 E7 ç τ 232...
  • Page 198 Code Page Selection Method/Country Standard Keyboard Country Honeywell Code Page Option Germany ISO/IEC646-21 4 84 Switzerland ISO /IEC 646-CH 6...
  • Page 199Unicode Key Maps 6E 70 71 72 73 74 75 76 77 78 79 7A 7B 7C 7D 7E 01...
  • Page 200A - 10
  • Page 201 Sample Symbols UPC-A Interleaved 2 of 5 0 123456 7890 1234567890 EAN-13 9 780330 290951 Code 128 Code 128...
  • Page 202 Matrix 2 of 5 6543210 GS1 DataBar (01)00123456789012 PDF417 Car Registration Data Matrix Test Symbol QR Code Aztec Numbers...
  • Page 2034-CB (4-State Customer Bar Code) 01,234,567094,987654321,01234567891 ID-tag (UPU 4-State) J18CUSA8E6N062315014880T
  • Page 204 Programming Chart 0 1 2 3 4 5 6 7 8 9
  • Page 205 Programming Chart A B C D E F Save Discard Reset Note: If you make an error while scanning...
  • Page 206Honeywell Scanning & Mobility 9680 Old Bailes Road Fort Mill, SC 29707 www.honeywellaidc.com VG1450-UG Rev A 12/14
downloadlike
ArtboardArtboardArtboard
Report Bug