Panasonic AWHE60HE User Manual

Page of 114
14
What to do when encountering problems in 
the basic shooting operations
If the trouble is not resolved by taking the action suggested 
below, refer to “Troubleshooting” (page 43 in the <Basics>).
When performing the operations  
using the wireless remote control
The unit does not move.
p
 Press the [CAM1], [CAM2], [CAM3] or [CAM4] button to 
select the unit which is to be operated. 
If only one unit is being used, it is normally selected using 
the [CAM1] button.
p
 Check that the IR ID switches have been set correctly. 
(Refer to pages 37 and 40 in the <Basics>.)
p
 If the unit’s status display lamp is off or lights up orange, it 
means that the unit’s power is not on. 
Refer to “Turning the power on” (page 8), and turn on the 
power.
p
 If the unit’s status display lamp does not blink even when 
the wireless remote control is operated near the unit’s 
wireless remote control signal light-sensing area, it means 
that the wireless remote control’s batteries have run down. 
Replace the batteries.
Multiple color bands (color bars) are displayed.
Press the [MODE] button to switch to the camera picture.
The menu screen is displayed.
Press the [MENU] button for 2 seconds to exit the camera 
menu.
The lens focus is not adjusted automatically.
Press the [A/FOCUS] button to switch to auto focusing.
(Auto focusing does not work during panning or tilting 
operations.)
The camera picture is too light or too dark.
1.   Press the [A/IRIS] button to switch the lens iris 
adjustment to auto.
2.   Press the [AUTO] button of [GAIN] to switch the gain 
adjustment to auto.
Something is wrong with the coloring of the 
camera pictures.
Refer to “Auto tracking white adjustment (ATW)” (page 25), and 
switch to “ATW”.
The camera menus are not displayed.
When color bar signals are output, the camera menus are 
not displayed with composite signals.
To operate the camera menus with composite signals, set the 
color bar display to OFF.
When performing the operations using the controller
The unit does not move.
p
 Select the unit to be operated by following the procedure 
below.
When the AW‑RP655 is connected:
Press the [1], [2], [3], [4] or [5] button of [CONTROL/
PREVIEW MONITOR OUT SEL].
When the AW‑RP555 is connected:
Press the [1], [2], [3], [4] or [5] button of [CONTROL].
When the AW‑RP50 is connected:
Refer to the Operating Instructions of the controller.
p
 If the [OPERATE] lamp on the controller is off, it means 
that the power of the controller is not on.
p
 If the unit’s status display lamp is off or lights up orange, it 
means that the unit’s power is not on.  
Refer to “Turning the power on” (page 8), and turn on the 
power.
Multiple color bands (color bars) are displayed.
Press the [MODE] button to switch to the camera picture.
The menu screen is displayed.
Press the [MENU] button to exit the camera menu.
The lens focus is not adjusted automatically.
Press the [EXT(AF)] button to switch to auto focusing.
(Auto focusing does not work during panning or tilting 
operations.)
The camera picture is too light or too dark.
1.   Press the [IRIS] button several times to turn on its lamp, 
and switch the lens iris adjustment to auto.
2.   Press the [GAIN] button several times to turn on its lamp, 
and switch the gain adjustment to auto.
Something is wrong with the coloring of the 
camera pictures.
Refer to “Auto tracking white adjustment (ATW)” (page 25), and 
switch to “ATW”.
The camera menus are not displayed.
When color bar signals are output, the camera menus are 
not displayed with composite signals.
To operate the camera menus with composite signals, set the 
color bar display to OFF.