Panasonic AWHE60HE User Manual
69
Controls and settings from web screen
(continued)
Transmission type
[Unicast port (AUTO), Unicast port (MANUAL),
[Unicast port (AUTO), Unicast port (MANUAL),
Multicast]
<Initial setting: Unicast port (AUTO)>
The transmission system for the H.264 images is selected
here.
The transmission system for the H.264 images is selected
here.
Unicast port
(AUTO)
(AUTO)
With this setting, up to 14 users can
access one camera at the same time.
When sending images from the unit,
“Unicast port(image)” is selected
automatically.
If there is no need to always use the
same port number for sending the
H.264 images in cases where the unit
is used in a network, for instance, it
is recommended that “Unicast port
(AUTO)” be selected.
access one camera at the same time.
When sending images from the unit,
“Unicast port(image)” is selected
automatically.
If there is no need to always use the
same port number for sending the
H.264 images in cases where the unit
is used in a network, for instance, it
is recommended that “Unicast port
(AUTO)” be selected.
Unicast port
(MANUAL)
(MANUAL)
With this setting, up to 14 users can
access one camera at the same time.
When sending images from the
camera, “Unicast port (MANUAL)”
must be set manually.
When sending H.264 images over
the internet, always use the same
communication-enabled port number
that is set in the broadband router
(hereafter, the “router”).
For further details, refer to the
operating instructions of the router
used.
access one camera at the same time.
When sending images from the
camera, “Unicast port (MANUAL)”
must be set manually.
When sending H.264 images over
the internet, always use the same
communication-enabled port number
that is set in the broadband router
(hereafter, the “router”).
For further details, refer to the
operating instructions of the router
used.
Multicast
With this setting, the number of users
who can access one camera at the
same time is unlimited.
When sending H.264 at the “Multicast”
setting, input the “Multicast address”,
“Multicast port”, and “Multicast TTL/
HOPLimit”.
who can access one camera at the
same time is unlimited.
When sending H.264 at the “Multicast”
setting, input the “Multicast address”,
“Multicast port”, and “Multicast TTL/
HOPLimit”.
p
When “Unicast port (MANUAL)” has been selected,
the “Unicast port(image)” must be set.
Note
Unicast port(image) [1024 to 50000]
(Only even numbers can be set)
(Only even numbers can be set)
<Initial setting: 32004>
The Unicast port number (used when sending images
from the unit) is input here.
The Unicast port number (used when sending images
from the unit) is input here.
Multicast address
[Setting range: 224.0.0.0 to 239.255.255.255]
<Initial setting: 239.192.0.20>
The Multicast IP address is input here.
The images are sent to the specified IP address.
The Multicast IP address is input here.
The images are sent to the specified IP address.
p
Input the address after checking which Multicast IP
addresses can be used.
Note
Multicast port [1024 to 50000]
(Only even numbers can be set)
(Only even numbers can be set)
<Initial setting: 37004>
The Multicast port number (used when sending images
from the unit) is input here.
The Multicast port number (used when sending images
from the unit) is input here.
p
If “Multicast” has been selected as the
“Transmission type” setting, the Multicast address
must be set.
must be set.
Note
Multicast TTL/HOPLimit [1 to 254]
<Initial setting: 16>
The Multicast TTL/HOP Limit is input here.
The Multicast TTL/HOP Limit is input here.
p
When sending H.264 images over the internet or VPN, the
images sent may not be displayed.
In a case like this, check with the network administrator.
In a case like this, check with the network administrator.
p
When displaying Multicast images using a personal
computer into which a multiple number of LAN cards have
been inserted, disable the LAN card that will not be used
to receive the images.
been inserted, disable the LAN card that will not be used
to receive the images.