Pelco WLV2500 User Manual
4
Pelco Manual C914M (7/96)
5.0 INSTALLATION
NOTE: Proper placement of the
transmit and receive antennas is
important for best reception.
Read Section 4.0, “Antenna Lo-
cation,” before installing the
equipment.
transmit and receive antennas is
important for best reception.
Read Section 4.0, “Antenna Lo-
cation,” before installing the
equipment.
Install the WLV500 receiver and WLV2000 transmit-
ter at the remote site where your camera will be. Install
the WLV500 transmitter and WLV2000 receiver at the
site where your video/audio monitor will be (refer to
Figure 1).
ter at the remote site where your camera will be. Install
the WLV500 transmitter and WLV2000 receiver at the
site where your video/audio monitor will be (refer to
Figure 1).
5.1 ENCLOSURE MOUNTING
Mount the enclosures. You can attach an enclosure di-
rectly to a flat mounting surface or you can use the ad-
justable mounting brackets that are supplied.
rectly to a flat mounting surface or you can use the ad-
justable mounting brackets that are supplied.
An enclosure can be mounted directly to a flat surface
if the enclosure will be at the same elevation and paral-
lel in both directions (vertically and horizontally) as
the enclosure for the receiver. Hardware is not supplied.
if the enclosure will be at the same elevation and paral-
lel in both directions (vertically and horizontally) as
the enclosure for the receiver. Hardware is not supplied.
NOTE: If you mount the WLV2000 receiver
enclosure directly to a flat surface, you will not
be able to adjust the enclosure in Section 5.4,
“Antenna Alignment,” for the best signal re-
ception.
enclosure directly to a flat surface, you will not
be able to adjust the enclosure in Section 5.4,
“Antenna Alignment,” for the best signal re-
ception.
To mount an enclosure to a pole using the adjustable
mounting brackets, refer to the manuals for the PA9000
adapter and PA102 pole mount to install the pole mount
and adapter. Then follow steps a through d in the next
paragraph.
mounting brackets, refer to the manuals for the PA9000
adapter and PA102 pole mount to install the pole mount
and adapter. Then follow steps a through d in the next
paragraph.
Figure 3. Multiple-System Interference
To mount an enclosure to a flat surface with the adjust-
able mounting brackets, refer to Figure 6 and perform
the following steps:
able mounting brackets, refer to Figure 6 and perform
the following steps:
1.
Fasten two of the four mounting brackets (item 12)
to the desired mounting surface. Install the brack-
ets 10.75 inches (27.31 cm) apart. Hardware is not
supplied.
to the desired mounting surface. Install the brack-
ets 10.75 inches (27.31 cm) apart. Hardware is not
supplied.
2.
Using the hardware items A, B, and C, attach the
four adjustable straps (item 13) to the brackets in-
stalled in (a) above. At this time do not tighten the
screws.
four adjustable straps (item 13) to the brackets in-
stalled in (a) above. At this time do not tighten the
screws.
3.
Using hardware items B, C, D, and E, attach the
other two mounting brackets to the enclosure.
other two mounting brackets to the enclosure.
4.
Attach the enclosure to the adjustable straps with
hardware items A, B, and C. The straps have mul-
tiple holes so that you can aim the enclosure to-
ward the opposite site. When you have the enclo-
sure positioned properly, tighten all screws. (If you
are installing a WLV2000 receiver enclosure,
tighten all screws just enough to keep the enclo-
sure from moving. The final tightening of the
screws will be done later.)
hardware items A, B, and C. The straps have mul-
tiple holes so that you can aim the enclosure to-
ward the opposite site. When you have the enclo-
sure positioned properly, tighten all screws. (If you
are installing a WLV2000 receiver enclosure,
tighten all screws just enough to keep the enclo-
sure from moving. The final tightening of the
screws will be done later.)
Proceed to Section 5.2, “Wiring.”