Leica 6007282 User Manual
8
Set-up and applications
Roteo 20HV/25H/35/35G - 1.2.0en
D
EN
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
To use the laser for inclined planes:
X
Set the laser in vertical mode, preferably on a tripod.
If setting on the ground, flip down the support plate for
stability.
If setting on the ground, flip down the support plate for
stability.
X
After the laser has self-leveled, set in manual or semi-
automatic mode.
automatic mode.
X
Loosen the knobs on either side {D-1} to partially
separate the mount from the laser.
separate the mount from the laser.
X
Move the laser to the approximate inclined position
and tighten slightly.
and tighten slightly.
X
Move to the final position and tighten further. See illus-
tration {K} in the back, inside cover of this manual.
tration {K} in the back, inside cover of this manual.
Set-up for ceiling work
The Roteo is perfect for the leveling of suspended ceil-
ings when used together with the wall mount and
magnetic ceiling grid target.
ings when used together with the wall mount and
magnetic ceiling grid target.
To attach the laser and wall mount to the first piece
of perimeter ceiling grid (Roteo 20HV/35/35G):
of perimeter ceiling grid (Roteo 20HV/35/35G):
X
Flip down the support plate {D-8}
X
Release the clamp {D-2} on top of the adjustable plate
{D-3}.
{D-3}.
X
Lock the clamp against the ceiling grid.
X
If the foot on the support plate is not touching the wall,
use the screw {D-9} to adjust.
use the screw {D-9} to adjust.
To move the laser up or down (Roteo 35/35G):
X
Turn on the laser and wait for it to self-level. The head
must be rotating before you can enter motorized
mount mode.
must be rotating before you can enter motorized
mount mode.
X
Press the motorized mount key {B-5} to activate the
mount. The motorized mount LED {B-11} will turn on
to indicate that the mount is now active.
mount. The motorized mount LED {B-11} will turn on
to indicate that the mount is now active.
X
To raise the motorized mount press the Plus key
{B-9}. Press the Minus key {B-8} to lower motorized
mount. Holding the key will result in fast movement;
short clicks will move the laser more precisely.
{B-9}. Press the Minus key {B-8} to lower motorized
mount. Holding the key will result in fast movement;
short clicks will move the laser more precisely.
Getting to work:
X
Raise the laser on the wall mount until the rotating
beam is at the same level as the perimeter ceiling grid.
Use the line created by the laser as a reference to
attach the perimeter grid to the wall.
beam is at the same level as the perimeter ceiling grid.
Use the line created by the laser as a reference to
attach the perimeter grid to the wall.
X
Lower the laser on the wall mount until the rotating
beam is striking the on-grade position on the
magnetic, ceiling grid target.
beam is striking the on-grade position on the
magnetic, ceiling grid target.
X
Adjust the height of the ceiling grid using the laser
beam on the target as your reference. See illustration
{G} in the back, inside cover of this manual.
beam on the target as your reference. See illustration
{G} in the back, inside cover of this manual.
S
et-up for layout or floor work
(Roteo 20HV/35/35G)
The Roteo can easily be used in the laydown or vertical
mode for laying out walls locations, transferring points
from the floor to the ceiling and plumb applications.
mode for laying out walls locations, transferring points
from the floor to the ceiling and plumb applications.
To use the laser in the vertical mode:
X
Flip down the support plate {D-8} and place the laser
in vertical mode on the floor.
in vertical mode on the floor.
X
If the support plate is not level, use the screw {D-9} to
adjust.
adjust.
X
Set up the laser over a control point by first pointing
the stationary beam downward, and then manually, or
the stationary beam downward, and then manually, or