Leica 6007285 User Manual
6
Set-up and applications
Roteo 20HV/25H/35/35G - 1.2.0en
D
EN
F
I
E
P
NL
DK
S
N
FIN
J
CN
ROK
PL
H
RUS
CZ
Wall Mount
{D} (Roteo 20HV/35/35G)
See the inside, front cover for illustrations of the Wall
Mount.
1) Attachment clamps for laser and mount
2) Clamp for ceiling grid
3) Adjustable plate
4) 5/8"-11 tripod mount (vertical setup)
5) Moves laser manually on mount
6) Holes for attaching mount to wall
7) Adjustable support for wall or ground stability
8) Screw to adjust support
9) Index notches for alignment
The wall mount can be used to move the laser up or
down on a ceiling grid. It can also be used when
installing walls and partitions to move the laser back and
forth for vertical alignment.
Mount.
1) Attachment clamps for laser and mount
2) Clamp for ceiling grid
3) Adjustable plate
4) 5/8"-11 tripod mount (vertical setup)
5) Moves laser manually on mount
6) Holes for attaching mount to wall
7) Adjustable support for wall or ground stability
8) Screw to adjust support
9) Index notches for alignment
The wall mount can be used to move the laser up or
down on a ceiling grid. It can also be used when
installing walls and partitions to move the laser back and
forth for vertical alignment.
Motorized Wall Mount (Roteo 35/35G)
Activating the motorized wall mount
Allow the laser to self-level. Note the position or the
beam.
Allow the laser to self-level. Note the position or the
beam.
X
Press the Motorized mount key {B-5} to activate the
mount. The motorized mount LED {B-11} will turn on
to indicate that the mount is now active (on the
Remote, press Scan/Rotation key {E-3, F-4} for 1.5
seconds).
mount. The motorized mount LED {B-11} will turn on
to indicate that the mount is now active (on the
Remote, press Scan/Rotation key {E-3, F-4} for 1.5
seconds).
X
To raise the laser press the Plus key {B-9}. Press the
Minus key {B-8} to lower the laser.
Minus key {B-8} to lower the laser.
Maximum movement
When the beam is at 0 on the adjustable plate, the laser
can be raised a maximum of 50 mm (2") and lowered a
maximum of 60 mm (2.25").
When the beam is at 0 on the adjustable plate, the laser
can be raised a maximum of 50 mm (2") and lowered a
maximum of 60 mm (2.25").
Wait until self-leveled
While the laser is moving on the mount it does not self-
level and the beam continues to rotate.
While the laser is moving on the mount it does not self-
level and the beam continues to rotate.
X
After moving the laser, wait a few seconds in case the
laser needs to self-level. Check that it is still on the
point or level desired and make adjustments if
needed.
laser needs to self-level. Check that it is still on the
point or level desired and make adjustments if
needed.
Automatic exit from mode
If you have not activated the wall mount for five minutes,
the laser will automatically exit from the motorized mount
mode and return to the previous mode. The Motorized
mount LED will turn off.
If you have not activated the wall mount for five minutes,
the laser will automatically exit from the motorized mount
mode and return to the previous mode. The Motorized
mount LED will turn off.
Troubleshooting
X
If the laser does not move on the mount, check that
the knobs {D-1} are tight enough to make the power
contact for the motor. The mount can also be
detached to check that the contacts are clean where
the laser and mount.
the knobs {D-1} are tight enough to make the power
contact for the motor. The mount can also be
detached to check that the contacts are clean where
the laser and mount.
Set-up and applications
Set-up for manual slopes
The Roteo can be used to manually create slopes for
special applications, stairways, sloped ceilings, etc.
special applications, stairways, sloped ceilings, etc.