Grizzly G0514X User Manual

Page of 96
<%*&)M$"M'$"M'7$"M(B[\#H^cXZ'$&'
"(*"
Aligning Table
IdZchjgZXjii^c\VXXjgVXnl]Zci]ZiVWaZ^h[^ghi
^chiVaaZY!i]ZiVWaZh]djaYWZVa^\cZYhdi]Vii]Z
b^iZg hadi ^h eVgVaaZa id i]Z WVcYhVl WaVYZ# I]^h
egdXZYjgZldg`hWZhil^i]V
(
¿
)
WaVYZ^chiVaaZY#
To align the table so the miter slot is parallel 
to the bandsaw blade:
1.
 BV`ZhjgZi]Vii]ZWaVYZ^higVX`^c\egdeZgan
VcYi]Vi^i^hXdggZXianiZch^dcZY#
2. 
9>H8DCC:8I76C9H6L;GDBEDL:G
3.
 AddhZc i]Z igjcc^dc Wdaih i]Vi hZXjgZ i]Z
igjcc^dchidi]ZiVWaZ#
4.
 EaVXZ Vc VXXjgViZ higV^\]iZY\Z Vadc\ i]Z
WaVYZ# I]Z higV^\]iZY\Z h]djaY a^\]ian idjX]
Wdi] i]Z [gdci VcY WVX` d[ i]Z WaVYZ# Note: 
Make sure the straightedge does not go 
across a tooth.
5.
 JhZV[^cZgjaZgid\Vj\Zi]ZY^hiVcXZ
WZilZZci]ZhigV^\]iZY\ZVcYi]Zb^iZghadi#
I]ZY^hiVcXZndjbZVhjgZh]djaYWZi]Z
hVbZViWdi]i]Z[gdciVcYi]ZWVX`d[i]Z
iVWaZhZZFigure 57#
6.
 6Y_jhi i]Z iVWaZ Vh cZZYZY [dg egdeZg Va^\c"
bZci#
7.
 I^\]iZci]Zigjcc^dcWdaih#
Figure 57. 
BZVhjg^c\[dgb^iZghadiidWZeVgVaaZa
l^i]WaVYZ#
IdZchjgZXjii^c\VXXjgVXnl]Zci]Z[ZcXZ^h[^ghi
^chiVaaZY! i]Z [ZcXZ h]djaY WZ Va^\cZY l^i] i]Z
b^iZghadi#
To align the fence parallel with the miter slot:
1.
 9>H8DCC:8I76C9H6L;GDBEDL:G
2.
 >[i]Z[ZcXZ^hbdjciZYdci]ZaZ[i"]VcYh^YZ
d[i]ZWaVYZ!gZbdkZ^iVcYgZbdjci^icZmiid
i]Zb^iZghadi#
3.
 AddhZc i]Z [djg XVe hXgZlh adXViZY dc i]Z
ide[VXZd[i]Z[ZcXZFigure 58#
Aligning Fence
Figure 58.
;djg[ZcXZXVehXgZlh#
4.
 6Y_jhii]Z[ZcXZ[VXZeVgVaaZal^i]i]ZZY\Zd[
i]Zb^iZghadi#
5.
 I^\]iZci]Z[djgXVehXgZlh!WZ^c\XVgZ[jacdi
idbdkZi]Z[ZcXZ#
Adjusting the fence parallel to the miter slot 
does not guarantee straight cuts. The miter 
slot may need to be adjusted parallel to the 
side of the blade. Refer to the "Aligning 
Table" instructions on this page.