Grizzly G0514X User Manual
<%*&)M$"M'$"M'7$"M(B[\#H^cXZ'$&'
"(*"
Aligning Table
IdZchjgZXjii^c\VXXjgVXnl]Zci]ZiVWaZ^h[^ghi
^chiVaaZY!i]ZiVWaZh]djaYWZVa^\cZYhdi]Vii]Z
b^iZg hadi ^h eVgVaaZa id i]Z WVcYhVl WaVYZ# I]^h
egdXZYjgZldg`hWZhil^i]V
^chiVaaZY!i]ZiVWaZh]djaYWZVa^\cZYhdi]Vii]Z
b^iZg hadi ^h eVgVaaZa id i]Z WVcYhVl WaVYZ# I]^h
egdXZYjgZldg`hWZhil^i]V
(
¿
)
WaVYZ^chiVaaZY#
To align the table so the miter slot is parallel
to the bandsaw blade:
to the bandsaw blade:
1.
BV`ZhjgZi]Vii]ZWaVYZ^higVX`^c\egdeZgan
VcYi]Vi^i^hXdggZXianiZch^dcZY#
2.
9>H8DCC:8I76C9H6L;GDBEDL:G
3.
AddhZc i]Z igjcc^dc Wdaih i]Vi hZXjgZ i]Z
igjcc^dchidi]ZiVWaZ#
4.
EaVXZ Vc VXXjgViZ higV^\]iZY\Z Vadc\ i]Z
WaVYZ# I]Z higV^\]iZY\Z h]djaY a^\]ian idjX]
Wdi] i]Z [gdci VcY WVX` d[ i]Z WaVYZ# Note:
Make sure the straightedge does not go
across a tooth.
Wdi] i]Z [gdci VcY WVX` d[ i]Z WaVYZ# Note:
Make sure the straightedge does not go
across a tooth.
5.
JhZV[^cZgjaZgid\Vj\Zi]ZY^hiVcXZ
WZilZZci]ZhigV^\]iZY\ZVcYi]Zb^iZghadi#
I]ZY^hiVcXZndjbZVhjgZh]djaYWZi]Z
hVbZViWdi]i]Z[gdciVcYi]ZWVX`d[i]Z
iVWaZhZZFigure 57#
I]ZY^hiVcXZndjbZVhjgZh]djaYWZi]Z
hVbZViWdi]i]Z[gdciVcYi]ZWVX`d[i]Z
iVWaZhZZFigure 57#
6.
6Y_jhi i]Z iVWaZ Vh cZZYZY [dg egdeZg Va^\c"
bZci#
7.
I^\]iZci]Zigjcc^dcWdaih#
Figure 57.
BZVhjg^c\[dgb^iZghadiidWZeVgVaaZa
l^i]WaVYZ#
IdZchjgZXjii^c\VXXjgVXnl]Zci]Z[ZcXZ^h[^ghi
^chiVaaZY! i]Z [ZcXZ h]djaY WZ Va^\cZY l^i] i]Z
b^iZghadi#
^chiVaaZY! i]Z [ZcXZ h]djaY WZ Va^\cZY l^i] i]Z
b^iZghadi#
To align the fence parallel with the miter slot:
1.
9>H8DCC:8I76C9H6L;GDBEDL:G
2.
>[i]Z[ZcXZ^hbdjciZYdci]ZaZ[i"]VcYh^YZ
d[i]ZWaVYZ!gZbdkZ^iVcYgZbdjci^icZmiid
i]Zb^iZghadi#
i]Zb^iZghadi#
3.
AddhZc i]Z [djg XVe hXgZlh adXViZY dc i]Z
ide[VXZd[i]Z[ZcXZFigure 58#
Aligning Fence
Figure 58.
;djg[ZcXZXVehXgZlh#
4.
6Y_jhii]Z[ZcXZ[VXZeVgVaaZal^i]i]ZZY\Zd[
i]Zb^iZghadi#
5.
I^\]iZci]Z[djgXVehXgZlh!WZ^c\XVgZ[jacdi
idbdkZi]Z[ZcXZ#
Adjusting the fence parallel to the miter slot
does not guarantee straight cuts. The miter
slot may need to be adjusted parallel to the
side of the blade. Refer to the "Aligning
Table" instructions on this page.
does not guarantee straight cuts. The miter
slot may need to be adjusted parallel to the
side of the blade. Refer to the "Aligning
Table" instructions on this page.