Yamaha RX-Z11 User Manual
Quick start guide
17
En
In
tr
od
ucti
ucti
on
1
Turn on the video monitor connected to this unit.
2
Press B
MASTER ON/OFF on the front panel inward
to the ON position.
After this unit is turned on, it takes approximately 20 seconds until this
unit produces sounds, and while “Please wait” appears in the front
panel display, this unit does not accepts the front panel operations and
stores the remote control operations. This unit performs the stored
remote control operations after “Please wait” disappears.
unit produces sounds, and while “Please wait” appears in the front
panel display, this unit does not accepts the front panel operations and
stores the remote control operations. This unit performs the stored
remote control operations after “Please wait” disappears.
3
Rotate the D
INPUT selector to set the input source
y
The recommended sound field program is set for each input source
(BD/HD DVD, etc.). You can also use various sound field programs
and other sound modes for playback. Refer to the following pages for
details:
The recommended sound field program is set for each input source
(BD/HD DVD, etc.). You can also use various sound field programs
and other sound modes for playback. Refer to the following pages for
details:
– see pages 64 and 86 to use various sound field programs
– see page 64 to turn on or off the sound effect
– see page 65 to use the pure direct mode for high fidelity sound
– see page 64 to turn on or off the sound effect
– see page 65 to use the pure direct mode for high fidelity sound
4
Start playback of the desired Blu-ray Disc/HD DVD
source on your player.
source on your player.
5
Rotate E
VOLUME to adjust the volume.
■ After using this unit...
Press A
MAIN ZONE ON/OFF to set this unit to the
standby mode.
This unit is set to the standby mode and consumes a small amount
of power in order to receive infrared signals from the remote
control. To turn on this unit from the standby mode, press AMAIN
ZONE ON/OFF on the front panel (or EPOWER on the remote
control). See page 43 for details.
of power in order to receive infrared signals from the remote
control. To turn on this unit from the standby mode, press AMAIN
ZONE ON/OFF on the front panel (or EPOWER on the remote
control). See page 43 for details.
■ Are you enjoying playback?
If there are some troubles with playback, check the settings as
follows.
follows.
No sound is output.
Are the speakers connected correctly?
 Check the speaker connection.
Are Your Blu-ray Disc/HD DVD player connected correctly?
 Check the connection of the Blu-ray Disc/HD DVD player.
Are the front speakers selected correctly?
 Press GSPEAKERS A or GSPEAKERS B.
Is volume setting correct?
 Adjust the volume level.
Does the Blu-ray Disc/HD DVD player play back correctly?
 Check the setting of the Blu-ray Disc/HD DVD player.
 Check the speaker connection.
Are Your Blu-ray Disc/HD DVD player connected correctly?
 Check the connection of the Blu-ray Disc/HD DVD player.
Are the front speakers selected correctly?
 Press GSPEAKERS A or GSPEAKERS B.
Is volume setting correct?
 Adjust the volume level.
Does the Blu-ray Disc/HD DVD player play back correctly?
 Check the setting of the Blu-ray Disc/HD DVD player.
No picture.
Is the video monitor connected correctly?
 Check the connection of the video monitor.
If the video monitor is connected to the HDMI OUT 1 jack of
this unit, is the “HDMI OUT SEL” setting correct?
 Set the operation mode selector to CAMP and then press
 Check the connection of the video monitor.
If the video monitor is connected to the HDMI OUT 1 jack of
this unit, is the “HDMI OUT SEL” setting correct?
 Set the operation mode selector to CAMP and then press
Is Blu-ray Disc/HD DVD player connected correctly?
 Check the connection of the video monitor.
Is the input source setting of the video monitor correct?
 Check the setting of the input source of the video monitor.
 Check the connection of the video monitor.
Is the input source setting of the video monitor correct?
 Check the setting of the input source of the video monitor.
Any other troubles?
Refer to “Troubleshooting” on pages 146 to 153 for other
troubles.
troubles.
Step 3: Turn on the power and start
playback
playback
Check the type of the connected speakers.
If the speakers are 6-ohm speakers, set “SPEAKER IMP.” to
“6
If the speakers are 6-ohm speakers, set “SPEAKER IMP.” to
“6
ΩMIN” before using this unit (see page 142).
Note
Automatic setup feature
To optimize the speaker settings for your listening room, use the
automatic setup feature. See pages 47 to 52 for details.
To optimize the speaker settings for your listening room, use the
automatic setup feature. See pages 47 to 52 for details.