Jenn-Air 8101P653-60 User Manual

• Only qualified personnel should install or service this range.

NOTE: User may experience some occasional circuit tripping if Ground
Fault Circuit Interrupter (GFCI) outlet or breaker is in use.

Electrical Grounding Instructions—This appliance is equipped with a
(three-pronged) grounding plug for your protection against shock
hazard and should be plugged directly into a properly grounded
receptacle. Do not cut or remove the grounding plug from this plug.

This appliance is equipped with a three-prong grounded type power cord. A grounded outlet must be provided. It is recommended that the outlet be located as
illustrated in the instructions.

If the outlet is to be mounted in either a left or a right adjacent cabinet, a clearance hole (1-1/2” – 3.18 cm) must be provided in the dividing wall between the
cabinets. NOTE: The free length of the appliance’s power cord is approximately 46 inches. In planning the location of the clearance hole and
outlet, the cord’s length should be considered.

Never test for gas leaks with an open flame. Apply a non-corrosive
leak detection fluid to all joints and fittings in the gas connection
between the supply line shut-off valve and the range. Include gas
fittings and joints in the range if connections were disturbed during
installation. Bubbles appearing around fittings and connections will
indicate a leak. If a leak appears, turn off supply line gas shut-off
valve,tighten connections, turn-on the gas supply line and retest for
leaks. When leak check is complete, wipe off all residue.

1. The appliance and its individual shutoff valve must be disconnected from the gas

supply piping system during any pressure testing of that system at test pressures
in excess of 1/2 lbs./sq. in. (3.5 kPa) (13.8 in. water column).

2. The appliance must be isolated from the gas supply piping system by closing its

individual manual shutoff valve during any pressure testing of the gas supply
piping system at test pressures equal to or less than 1/2 lbs./sq. in. (3.5 kPa) (13.8
in. water column).

1. Slide range forward to disengage range from the anti-tip bracket.
2. Shut off gas supply to appliance.
3. Disconnect electrical supply to appliance, if equipped.
4. Disconnect gas supply tubing to appliance.
5. Reverse procedure to reinstall. If gas line has been disconnected,

check for gas leaks after reconnection.

6. To prevent range from accidentally tipping, range must be secured to the floor by sliding rear leveling leg into the anti-tip bracket.

A qualified servicer should disconnect and reconnect the gas supply. The servicer MUST follow installation instructions provided with the gas

appliance connector and the warning label attached to the connector.

When your range requires service or replacement parts, contact your dealer or authorized service agency. Please give the complete model and
serial number of the range which is located on the flip-up plate at the rear of upper left-hand corner or center of backguard.

Your range may not be equipped with some of the features referred to in this manual.

Propane conversion is to be performed by a JENN-AIR AUTHORIZED 
SERVICER (or other qualified agency) in accordance with the
manufacturer’s instructions and all codes and requirements of the
authority having jurisdiction. Failure to follow instructions could result in 
serious injury or property damage. The qualified agency performing this
work assumes responsibility for this conversion.

Warranty is void on Jenn-Air equipment installed other than as

recommended by manufacturer.

The installation of this appliance must conform with local codes or, in
the absence of local codes, with the National Fuel Gas Code, ANSI
Z223.1-Latest Edition, or, in Canada, CAN/CGA-B149 Installation Code,
Latest Edition.

This appliance, when installed, must be electrically grounded in 
accordance with local codes or, in the absence of local codes, with the
National Electrical Code ANSI/NFPA No. 70-Latest Edition, or, in Canada,
current CSA Standard C22.1 Canadian Electrical Code, Part 1.

Follow accompanying ducting instructions carefully. This appliance is
designed to always be vented outdoors. The Countertop Cutout, Cabinet
Front Cutout and Duct Opening should be prepared according to the
illustration in the instructions given.

Locate appliance away from combustible materials such as window
curtains or wall decorations.

NEVER USE A METAL BLADE TO PRY KNOB OFF. IF KNOB CANNOT BE
EASILY REMOVED, TUCK THE FOLDS OF A CLOTH DISHTOWEL UNDER THE
KNOB AND PULL THE TOWEL UPWARD WITH STEADY, EVEN PRESSURE

.

Never cover control knobs or surrounding control surface with uten-
sils, towels, or other objects. Never obstruct free air passage past the
control knobs. The knob openings have been sized to properly control
air entry to the interior of the appliance during operation.

In The Commonwealth of Massachusetts:
This product must be installed by a licensed plumber or gas fitter
when installed within the Commonwealth of Massachusetts.

A “T” handle type manual gas valve must be installed in the gas
supply line to this appliance.

A flexible gas connector, when used, must not exceed a length of
three (3) feet/36 inches.

Never tighten appliance regulator to more than 35 ft-lbs of torque. Always
use an approved pipe joint compound resistant to the action of LP gas.

Gas leaks may occur in your system and result in a dangerous
situation. Gas leaks may not be detected by smell alone. Gas suppliers
recommend you purchase and install an UL approved gas detector.
Install and use in accordance with manufacturer's instructions.

ELECTRICAL POWER AND GAS MUST BE TURNED OFF PRIOR TO CONVERSION.

If the line pressure supplying the appliance pressure regulator exceeds
14” W.C. (any gas), the external regulator must be installed in the gas line
ahead of the appliance regulator to reduce the pressure to no more than
14” W.C. Failure to do this can result in malfunction and damage to the
appliance.

Leak testing of the appliance shall be conducted by the installer according to the
instructions given.

Gas supply piping MUST conform to all local, municipal and state building codes
and local utility regulations.

NOTE: In Canada, gas utilization codes prohibit use of street elbows. Use standard
pipe elbows and make modification to these instructions as necessary.

All supply piping, except as noted, should use common National Pipe Thread
(N.P.T.). For all pipe connections use an approved pipe joint compound resistant to
the action of LP gas.

This appliance is designed for use with the appliance gas pressure regulator 
supplied with this appliance. It must be installed in the gas line ahead of the gas
manifold entrance. It is preset for use with natural gas and must be converted, as
described in the instructions given, for use with LP(propane) gas

A GAS SHUT-OFF VALVE SHOULD BE PUT IN AN ACCESSIBLE LOCATION IN THE
SUPPLY LINE AHEAD OF THE RANGE, FOR TURNING ON AND TURNING OFF 
GAS SUPPLY.