Cornelius FlavorFusion Series User Manual
FlavorFusion Installation Manual
Publication Number: 621057601INS
- 18 -
© 2005-2006, IMI Cornelius Inc.
D
IAGNOSTICS
G
UIDE
FOR
F
LAVOR
F
USION
K
EYPAD
L
IGHTING
Contact your local syrup or beverage equipment distributor for additional information and troubleshooting
of beverage system.
of beverage system.
Observations of LED Lighting on Customer Interface Keypad
Symptom
Cause
Remedy
1
Bonus Flavor Icon and/
or Drink Icon LEDs (see
FIGURE 4) are ON
continuously with four
quick flashes every 30
seconds.
or Drink Icon LEDs (see
FIGURE 4) are ON
continuously with four
quick flashes every 30
seconds.
A. This indicates a poor
connection in the lighting
synchronization harness
that connects the interface
boards together.
connection in the lighting
synchronization harness
that connects the interface
boards together.
A. Turn the keyswitch to disconnect
power to the interface boards. Check the
electrical connections between the
harnesses that interconnect the right
side of all interface boards together. Turn
back the keyswitch to reconnect power.
power to the interface boards. Check the
electrical connections between the
harnesses that interconnect the right
side of all interface boards together. Turn
back the keyswitch to reconnect power.
2
Bonus Flavor Icon and/
or Drink Icon LEDs (see
FIGURE 4) are not in
sync with the lighting
sequence,
or Drink Icon LEDs (see
FIGURE 4) are not in
sync with the lighting
sequence,
B. This may result over time
as the lighting sequence
between push button pads
can become slightly out of
synchronization.
as the lighting sequence
between push button pads
can become slightly out of
synchronization.
B. Unplugging the unit and performing a
power up will re-synchronize the lighting
sequence.
power up will re-synchronize the lighting
sequence.
3
Keypad LED lighting is
not working
not working
A. Poor connection between
interface board and keypad
PCB
interface board and keypad
PCB
A. Turn the keyswitch to disconnect
power at the interface boards. Check
harness connections at each interface
board.
power at the interface boards. Check
harness connections at each interface
board.
B. Keypad LED's are burnt
out
out
B. Turn the keyswitch to disconnect
power at the interface boards. Unplug
the ribbon cable from one interface
board and test it by plugging it into the
neighboring interface board. If the
keypad still doesn't light up replace the
keypad PCB.
power at the interface boards. Unplug
the ribbon cable from one interface
board and test it by plugging it into the
neighboring interface board. If the
keypad still doesn't light up replace the
keypad PCB.
C. Interface board is
defective.
defective.
C. Turn the keyswitch to disconnect
power at the interface boards. Unplug
the ribbon cable from one interface
board and test it by plugging it into the
neighboring interface board. If the LED's
light up the interface board is defective.
Replace the interface board.
power at the interface boards. Unplug
the ribbon cable from one interface
board and test it by plugging it into the
neighboring interface board. If the LED's
light up the interface board is defective.
Replace the interface board.
D. Corrosion at connector
between keypad and ribbon
cable.
between keypad and ribbon
cable.
D. Replace keypad circuit board and
ribbon cable.
ribbon cable.
E. Main control board is
defective.
defective.
E. Replace the main control board.
4
During standby mode,
the brand and bonus
LED icons do not
alternate back and forth
- instead they light
together.
the brand and bonus
LED icons do not
alternate back and forth
- instead they light
together.
Bonus buttons are
incorrectly programmed as
brand buttons, or vice versa.
incorrectly programmed as
brand buttons, or vice versa.
Check the programming of each keypad
and set each button as CW, PW, or
timed dispense based upon the flavor
lineup.
and set each button as CW, PW, or
timed dispense based upon the flavor
lineup.