Zanussi SIP 3.0.2 User Manual
Problem Possible solution
The grill, ovens and timer do not work.
The grill and top oven work but the main oven does not.
The timer does not work.
The oven is not cooking evenly.
The indicator neons are not working correctly.
The oven fan is noisy.
The oven temperature is too high or too low.
•
•
•
•
•
•
•
•
•
•
•
•
•
Check that the appliance has been wired in to the
appliance supply and is switched on at the wall.
Check that the main appliance fuse is working.
If you have checked the above: Allow the appliance
to cool for a couple of hours. The appliance should
now be working normally.
appliance supply and is switched on at the wall.
Check that the main appliance fuse is working.
If you have checked the above: Allow the appliance
to cool for a couple of hours. The appliance should
now be working normally.
Check that the time of day has been set on the clock.
Check that the instructions for the operation of the
timer are being closely followed.
timer are being closely followed.
Check that the appliance is correctly installed and
is level.
Check that the recommended temperatures and
shelf positions are being used.
is level.
Check that the recommended temperatures and
shelf positions are being used.
Check that you have selected only the function you
require. Ensure all other controls are in the off position.
require. Ensure all other controls are in the off position.
Check that the oven is level.
Check that the shelves and bakeware are not vibrating
in contact with the oven back panel.
Check that the shelves and bakeware are not vibrating
in contact with the oven back panel.
m
Check that the recommended temperatures and
shelf positions are being used. Be prepared to adjust
the temperature up or down to achieve the
results you want.
shelf positions are being used. Be prepared to adjust
the temperature up or down to achieve the
results you want.
Installation
Installation instructions
This appliance must be earthed.
• If your appliance has been damaged in transit,
contact your supplier immediately. Do not attempt
to install it.
to install it.
• Your appliance left the factory fully packaged to
protect it from damage. If it is delivered without
packaging and damage has occurred, the
manufacturer cannot accept responsibility. Contact
your supplier for advice.
packaging and damage has occurred, the
manufacturer cannot accept responsibility. Contact
your supplier for advice.
• Once the packaging has been removed the
appliance should only be moved by hand. Do not
use a sack barrow or any other aid to lift the
appliance as damage may occur. Do not carry the
appliances at the doorhandle.
use a sack barrow or any other aid to lift the
appliance as damage may occur. Do not carry the
appliances at the doorhandle.
• To move the appliance, open the oven door and lift
the appliance by holding inside the top of the
compartment.
compartment.
• This is a type X appliance, which means it is
freestanding and can be fitted with cabinets on one
or both sides.
• Sidewalls, which are above hob level, should be
protected by heat resistant non-combustible
material and must not be nearer than 40mm to the
hob side.
material and must not be nearer than 40mm to the
hob side.
• A nominal air gap of 5mm at either side of the
appliance is required to enable the appliance to be
moved into position.
moved into position.
• Always ensure an air gap is maintained at hotplate
level. Tiles or other forms of deep wall covering
level. Tiles or other forms of deep wall covering
should not obscure this gap.
• Overhanging surfaces or a cooker hood should be
a minimum of 685mm above the hob.
• It is important to ensure that the appliance is level
after installation. Levelling feet are fitted to the
appliance to accommodate uneven floors.
appliance to accommodate uneven floors.
Adjustment of levelling feet
The cooker stands on 4 levelling feet. It is required to
confirm the appliance is correctly levelled before
confirm the appliance is correctly levelled before
!
WARNING!
19