Panasonic CY-VM7203W User Manual
40
English
CY-VM7203W
41
English
CY-VM7203W
Troubleshooting
(Continued)
39
40
Product Servicing
If the suggestions in the charts do not solve the problem,
we recommend that you take it to your nearest authorized
Panasonic Service Center. The product should be serviced
only by a qualifi ed technician.
we recommend that you take it to your nearest authorized
Panasonic Service Center. The product should be serviced
only by a qualifi ed technician.
Replacing the Fuse
Use fuses of the same specifi ed rating (3 A). Using
different substitutes or fuses with higher ratings, or
connecting the unit directly without a fuse, could cause
fi re or damage to the unit.
If the replacement fuse fails, contact your nearest
Panasonic Service Center for service.
different substitutes or fuses with higher ratings, or
connecting the unit directly without a fuse, could cause
fi re or damage to the unit.
If the replacement fuse fails, contact your nearest
Panasonic Service Center for service.
If the Unit Fails to Operate
Reset switch
Insert a hard, slender stick into the hole and push the
switch.
Insert a hard, slender stick into the hole and push the
switch.
IMPORTANT
Press the switch only when the unit fails to operate with
any buttons. (Stored settings and adjustments are not
cleared.) If the unit fails to return to normal condition, call
the nearest Panasonic Service Center and ask for repairs.
Note:
If the ID-CODE has been already set, you will be asked
Press the switch only when the unit fails to operate with
any buttons. (Stored settings and adjustments are not
cleared.) If the unit fails to return to normal condition, call
the nearest Panasonic Service Center and ask for repairs.
Note:
If the ID-CODE has been already set, you will be asked
to enter the ID-CODE right after the unit is restarted.
Cleaning this Unit
When the unit is dirty, wipe the surface of the display
using the Wiping Cloth (supplied).
Cleaning without the supplied cloth
using the Wiping Cloth (supplied).
Cleaning without the supplied cloth
Moisten the soft cloth in dishwashing soap diluted
with water and wring well.
Wipe lightly. Go over the same surface with a dry
cloth.
Caution
If water drops or similar wet substances get inside
the monitor, it may cause a malfunction.
Note:
Since there is the possibility of water drops getting
Since there is the possibility of water drops getting
inside of the unit, do not directly apply cleanser to the
surface.
surface.
Do not scratch the screen with your nails or other hard
objects. The resulting scratches or marks will obscure
the images.
the images.
Caution on Cleaning
Your product is designed and manufactured to ensure a
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other
solvents.
minimum of maintenance. Use a dry soft cloth for routine
exterior cleaning. Never use benzine, thinner or other
solvents.
Pesticide
Alcohol
Thinner
Benzine
Wax
Maintenance
Specifi cations
General
Power supply:
DC 12 V (11 V–16 V), test
voltage 14.4 V,
voltage 14.4 V,
negative
ground
Current consumption:
Less than 1.0 A
Maximum power output
(For built-in speaker):
(For built-in speaker):
0.7 W
Video input signal:
Composite video signal, 1.0
Vp-p (75
Vp-p (75
)
Audio input sensitivity:
2 Vrms
Video output signal:
Composite video signal, 1.0
Vp-p (75
Vp-p (75
)
Dimensions (W
HD): 17850165 mm
Weight: 1.6
k
Monitor
Liquid crystal panel:
7 inches wide
Screen dimensions (W
HD):
143
79163 mm
Number of pixels:
336 960 pixels
(234
vertical
480 horizontal
3)
Valid pixel ratio:
Over 99.99 %
Display method:
Transparent color fi lter
format
format
Drive method:
TFT (Thin Film Transistor)
active matrix format
active matrix format
Light source:
Internal light (Built-in small
fl uorescent lamp)
fl uorescent lamp)
Note:
Specifi cations and design are subject to modifi cation
Specifi cations and design are subject to modifi cation
without notice due to improvements.
Some fi gures and illustrations on this manual may be
different from your product.