Crown AMB-5 User Manual
Page 10
IQ Mixer / Multiplexer Hardware Installation
Rev. 0
3 Hardware Installation
The installation of an IQ mixer/multiplexer consists
of two major parts: installing the hardware and con-
figuring the software. This manual deals only with
hardware installation. Refer to the appropriate soft-
ware manual for instructions in setting up and oper-
ating your unit.
of two major parts: installing the hardware and con-
figuring the software. This manual deals only with
hardware installation. Refer to the appropriate soft-
ware manual for instructions in setting up and oper-
ating your unit.
Provide adequate cooling if the unit will be used in a
hot environment.
hot environment.
Allow one empty rack space (1.75
inches or 4.4 cm.) between each unit if more than
four units will be stacked in a cabinet.
four units will be stacked in a cabinet.
Each empty
rack space should be sealed with a blank rack
panel.
panel.
The hardware installation is divided into 4 steps:
1) connecting to a host computer, 2) connecting to
the Crown Bus, 3) connecting the audio inputs and
outputs and 4) connecting auxiliary devices.
1) connecting to a host computer, 2) connecting to
the Crown Bus, 3) connecting the audio inputs and
outputs and 4) connecting auxiliary devices.
3.1 Connecting to a Host Computer (Step 1)
An IQ host computer is an IBM
®
PC compatible or
Apple
®
Macintosh computer which is used to con-
figure or control/monitor part or all of an
IQ System.
Depending upon the design of your
IQ System, it
may or may not require a host computer during
normal operation.
normal operation.
How the mixer/multiplexer will be used will deter-
mine whether or not it will need to be connected
directly to a host computer. If the unit will be con-
nected to the Crown Bus it will not need to be
connected directly to a host computer. The following
circumstances require connection to a host com-
puter:
mine whether or not it will need to be connected
directly to a host computer. If the unit will be con-
nected to the Crown Bus it will not need to be
connected directly to a host computer. The following
circumstances require connection to a host com-
puter:
• If a Crown Bus will not be used, the mixer/mul-
tiplexer will need to be connected to a host
computer so the software inside the unit can
be configured. Afterward, if manual control is
not required, the host computer can be discon-
nected.
computer so the software inside the unit can
be configured. Afterward, if manual control is
not required, the host computer can be discon-
nected.
• If the mixer/multiplexer must be configured be-
fore it is installed into an IQ System, it must be
connected directly to a host computer for con-
figuration. The onboard battery of the unit will
maintain its software configuration for up to 60
days without it being plugged into an AC
source.
connected directly to a host computer for con-
figuration. The onboard battery of the unit will
maintain its software configuration for up to 60
days without it being plugged into an AC
source.
• If the mixer/multiplexer will be used as an IQ
interface (Option 1) it will need to be con-
nected directly to a host computer.
nected directly to a host computer.
One of the advantages of connecting directly to a
host computer is that a separate IQ interface (IQ-
INT) is not required. If you plan to configure the unit
host computer is that a separate IQ interface (IQ-
INT) is not required. If you plan to configure the unit
Fig. 3.1 An IQ System with a PC Host Computer and Two Mixer/Multiplexers
ENABLE
DSPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
ENABLE
DSPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
ENABLE
CH1
CH2
ODEP
POWER
OFF
IOC
SPI
CROWN BUS LOOP 1
CROWN BUS LOOP 2
RS232