Keating Of Chicago 2006 User Manual
STEP 2 PRESS all 3 buttons in sequence: left-center-
right. The BEEPER will BEEP. If BEEPER
does not BEEP, the timer is defective. STOP
TESTING. Reset procedure is completed
when 1:00 appears on the digital display.
does not BEEP, the timer is defective. STOP
TESTING. Reset procedure is completed
when 1:00 appears on the digital display.
DIGITAL TIMER (PART # 030834)
PROGRAMMING
To program the timers, the unit must be in
the idle mode. Press and hold the set but-
ton for approximately two seconds. The
display will show “SEt”. Press the button
for the channel to be programmed. The
the idle mode. Press and hold the set but-
ton for approximately two seconds. The
display will show “SEt”. Press the button
for the channel to be programmed. The
display will show the current setting for that channel.
Use the up or down button to increment or decrement
the setting. When the setting is correct, press and hold
the set button again for approximately two seconds.
The display will show "StO" for approximately two sec-
onds and the timer will return to normal operation.
Repeat the process as necessary for the other timers.
Use the up or down button to increment or decrement
the setting. When the setting is correct, press and hold
the set button again for approximately two seconds.
The display will show "StO" for approximately two sec-
onds and the timer will return to normal operation.
Repeat the process as necessary for the other timers.
OPERATING LOGIC
When the timer is powered up, the display will show the
time setting for the channel that was operated last and
the relay output contacts will be open. To start a cycle,
press the desired channel button (1-3). The display will
begin to countdown from the preset time setting and
the relay output contacts will close. During the
countdown the colon will flash at a one-second rate.
When the countdown has reached "00:00" the relay
output contacts will open, the display will flash, and the
audible alarm will sound. To cancel the audible alarm,
press any button.
time setting for the channel that was operated last and
the relay output contacts will be open. To start a cycle,
press the desired channel button (1-3). The display will
begin to countdown from the preset time setting and
the relay output contacts will close. During the
countdown the colon will flash at a one-second rate.
When the countdown has reached "00:00" the relay
output contacts will open, the display will flash, and the
audible alarm will sound. To cancel the audible alarm,
press any button.
PAUSE FEATURE
To pause a cycle in progress, press any button. The
relay output contacts will open, the display will flash,
and the countdown will pause. To resume the
countdown, press any button. The display will resume
the normal countdown and the relay output contacts
will close.
relay output contacts will open, the display will flash,
and the countdown will pause. To resume the
countdown, press any button. The display will resume
the normal countdown and the relay output contacts
will close.
CANCELING A CYCLE
To cancel a cycle in progress press and hold any
button for approximately two seconds. The relay output
contacts will open and the display will show the time
setting for the channel last used.
button for approximately two seconds. The relay output
contacts will open and the display will show the time
setting for the channel last used.
DRAINING
ALWAYS SHUT THE FRYER OFF COMPLETELY
BEFORE DRAINING. THE FRYER SHOULD BE
DRAINED ONLY UNDER THE SUPERVISION OF
PROPERLY TRAINED PERSONNEL. A DRAIN PIPE
AND COVERED CONTAINER SUITABLE FOR USE
WITH HOT OIL SHOULD BE USED TO ENSURE THE
SAFETY OF THE OPERATOR.
BEFORE DRAINING. THE FRYER SHOULD BE
DRAINED ONLY UNDER THE SUPERVISION OF
PROPERLY TRAINED PERSONNEL. A DRAIN PIPE
AND COVERED CONTAINER SUITABLE FOR USE
WITH HOT OIL SHOULD BE USED TO ENSURE THE
SAFETY OF THE OPERATOR.
1.
Operator should be outfitted with proper attire
including:
including:
–Oil and heat resistant gloves
–Oil and heat resistant apron
–Safety goggles
–Oil and heat resistant footwear
–Oil and heat resistant apron
–Safety goggles
–Oil and heat resistant footwear
Figure 3-2
2.
Turn off the fryer and open the door.
3.
Put suitable container under drain valve (for Safe &
Easy models, slide filter onto rails inside of fryer or
filter cabinet).
Easy models, slide filter onto rails inside of fryer or
filter cabinet).
4.
• Front Drain: Drain oil from fryer by slowly
turning handle. The drain will be completely
open after 1/4 turn.
open after 1/4 turn.
• Rear Drain: Pull black knob forward slowly.
5.
After fryer drains, close the drain valve.
6.
Filtering may be done at this step - refer to filter
manual.
manual.
CLEANING AND BOIL-OUT
When cleaning and boiling out your fryer use Keating
Sea Powder and Keating Klenzer to keep your fryer in
top condition. Keating Sea Powder dissolves any grease
build up — even carbonized grease in fryer vessels —
one of the leading causes of premature oil breakdown.
Once your fryer vessel is clean, use Keating Klenzer, the
finest dry stainless steel polish available, to restore your
Keating Incredible Frying Machine
Sea Powder and Keating Klenzer to keep your fryer in
top condition. Keating Sea Powder dissolves any grease
build up — even carbonized grease in fryer vessels —
one of the leading causes of premature oil breakdown.
Once your fryer vessel is clean, use Keating Klenzer, the
finest dry stainless steel polish available, to restore your
Keating Incredible Frying Machine
®
’s (IFM) exterior to its
original luster.
7
11::0000
Side view of Safe & Easy Filter