ZyXEL Communications Vantage Access User Manual
Chapter 21 WAN Device
Vantage Access User’s Guide
339
The following table describes the labels in this screen. Refer to
for
other field descriptions.
Table 157 TR-098 Amendment 1: WAN Device: WANDSLLinkConfig
PARAMETER NAME
VALUE
Enable
This field displays 1 to indicate that the DSL link is active; otherwise, this
field displays 0.
field displays 0.
LinkStatus
This field displays the link status (Up, Down, Initializing or Unavailable).
LinkType
This field displays the type for this DSL link.
EoA sets the device to use the bridged Ethernet over ATM (RFC2684) link
type.
IPoA sets the device to use the routed IP over ATM (RFC2684) link type.
PPPoA sets the device to use the PPP over ATM (RFC2364) link type.
PPPoE sets the device to use the PPP over Ethernet on bridged Ethernet
over ATM (RFC2516, RFC2684) link type.
CIP sets the device to use the Classical IP over ATM (RFC1577) link type.
Unconfigured means an unknown link type.
EoA sets the device to use the bridged Ethernet over ATM (RFC2684) link
type.
IPoA sets the device to use the routed IP over ATM (RFC2684) link type.
PPPoA sets the device to use the PPP over ATM (RFC2364) link type.
PPPoE sets the device to use the PPP over Ethernet on bridged Ethernet
over ATM (RFC2516, RFC2684) link type.
CIP sets the device to use the Classical IP over ATM (RFC1577) link type.
Unconfigured means an unknown link type.
AutoConfig
This field displays whether the auto-configuration feature is enabled or
disabled for this DSL link.
disabled for this DSL link.
ModulationType
This field displays the type of modulation used on the interface associated
to this DSL link.
to this DSL link.
DestinationAddress
This field displays the destination address for the DSL link. The type of
address you enter varies depending on the connection type.
This field displays the VCI/VPI for a PVC connection.
This field displays an ATM connection name or ATM address for an SVC
connection.
address you enter varies depending on the connection type.
This field displays the VCI/VPI for a PVC connection.
This field displays an ATM connection name or ATM address for an SVC
connection.
ATMEncapsulation
This field displays the encapsulation (LLC or VCMUX) to use for this DSL
link.
link.
FCSPreserved
This field displays 1 to include a checksum in the ATM payload for error
correction.
0 means the checksum is not included in the ATM payload. No error
correction is available.
correction.
0 means the checksum is not included in the ATM payload. No error
correction is available.
VCSearchList
This field displays the VCI/VPI number pairs (separated by a comma) the
link uses to establish a connection if the destination address specified
cannot be reached.
link uses to establish a connection if the destination address specified
cannot be reached.
ATMAAL
This field displays the ATM Adaptation Layer (AAL) the link uses.
ATMTransmittedBlocks
This field displays the number of ATM blocks transmitted successfully.
ATMReceivedBlocks
This field displays the number of ATM blocks received successfully.
ATMQoS
Select the ATM Quality of Service (QoS) method to use on this link.
ATMPeakCellRate
This field displays the peak cell rate (between 0 and 4294967295) for the
upstream traffic in cells per second.
upstream traffic in cells per second.
ATMMaximumBurstSize
This field displays the maximum burst rate (between 0 and 4294967295)
for the upstream traffic in cells.
for the upstream traffic in cells.
ATMSustainableCellRate
This field displays the sustainable cell rate (between 0 and 4294967295) for
the upstream traffic in cells per second. This value is used for traffic
shaping.
the upstream traffic in cells per second. This value is used for traffic
shaping.
AAL5CRCErrors
This field displays the number of AAL5 layer cyclic redundancy check
errors.
errors.