Wibur Curtis Company TCO-308 User Manual

PROGRAMMING ONLY REQUIRED IF FACTORY SETTINGS MUST BE CHANGED

Changing the ADS™ System Program

Your ADS System features a dynamic memory. In the event of a power loss it will remember ALL program settings.

IMPORTANT – Before entering the program mode, allow the unit to reach brewing temperature, then press the BREW
button to dispense at least 12 ounces of water. This is to clear any air that may be trapped within the water lines.

CONFIRM/RESET BREW TEMPERATURE - Factory Preset to 204º

ENTER THE PROGRAMMING MODE #1:

Press

for two seconds, then RELEASE.

will start blinking. Each blink equals 2º F, starting at 170º (max. temp. 210º F or 21 blinks).

To change Temperature, press and HOLD

will start QUICK flashing. Each QUICK flash equals 2º F.

After reaching 210º, temperature starts over at 170º.

RELEASE when the desired temperature is reached. The newly set temperature will now be displayed.

To set and exit, press .

For ALL functions you must first enter the programming mode.

Turn OFF the power from the Control Panel by pressing .

Press and HOLD and press and RELEASE .

Continue HOLDING

until

starts blinking; RELEASE.

ENTERING THE PROGRAM MODE #1

CHANGE BREW VOLUME - CONCENTRATE

ENTER THE PROGRAMMING MODE #1

Press and HOLD until hot water starts running from sprayhead; then RELEASE.

When desired volume is reached, press

again to stop flow.

To set and exit, press .

CHANGE BREW VOLUME - DILUTION

ENTER THE PROGRAMMING MODE #1

Press and HOLD until cold water starts flowing from dilution faucet; then RELEASE.

When desired volume is reached, press

again to stop flow.

To set and exit, press .

STEPS TO

PROGRAMMING

WARNING These steps
involve working with hot
water. Scalding may occur if

care is not taken against spilling.

Brew Temperature – Factory Pre-Set to 204°F

Function to set brew temperature, 170° to 210°F. Brew temperature will be indicated by READY-TO-BREW light blinking.

BREW VOLUME - Factory Preset to Brewer Requirements

CHANGING THE DRIP MODE (DWELL TIME) FEATURE

READY TO BREW

Illustrated Parts List - TCTD-35/35S Curtis

Iced Tea Brewer

1
2
3
4
5
6
7
8
9
10
11
12
13
14
14A
15
16

WC-3322
WC-3647
WC-3320
WC-3201
WC-3358
WC- 750
WC-5450
WC-2977-01
WC-39260
WC-2965
WC-2906
WC-8556
WC- 895
WC-58017
WC-58021
WC-3502
WC-8531

BASKET, WIRE 6.4 DIA PTTD/TCTD USE W/WC-3320
STRAINER BT-10 BREWCONE (EXCEPT PARADISE)
BREW CONE W/HANDLE 8.8” D W/STRAINER
HANDLE, BREW CONE BLACK
BREWCONE ASSY, W/WC-3320, WC-3322 & WC-3647
CONTROL BOARD 120V 60Hz PTTD/TCTD
COVER, TOP BREWER
FITTING ASSY, SPRAYHEAD W/O-RING
MEMBRANE CONTROL PANEL, TCTD
SPOUT, BYPASS ASSY
SPRAYHEAD, BLUE .178 DIA ORF
HEAT SINK ASSY DV
VALVE, DUAL INLET 120V 10W
COVER, CENTER WRAP TCTD-35S
COVER, FRONT CENTER WRAP TCTD-35
LEG, 8-32 STD SCREW BUMPER
RAIL, BASE TCTD

DESCRIPTION

PART N

PART Nººººº

ITEM

Continued – Page 3

TO ACCESS BREW CYCLE COUNTER

ENTER THE PROGRAMMING MODE #2:

will now start a pattern of LONG and SHORT blinks.

This pattern identifies the number of brew cycles. SHORT blinks indicate the brew number from one [1] to nine [9].
LONG blinks separate the 1’s, 10’s, 1,000’s and 10,000’s.

BREW CYCLE COUNTER

Note: Dwell time setting has an affect on
dilution water flow (even though the Drip
Mode starts at the end of brewcycle). Drip
modes set at 7 minutes or less results in

pulsing dilution flow. Drip modes set at 8 minutes or
more results in continuous flow of dilution water.

For ALL functions you must first enter the programming mode.

Turn OFF the power from the Control Panel by pressing .

Press and HOLD and press and RELEASE .

Continue HOLDING until

STOPS blinking; RELEASE.

ENTER THE PROGRAM MODE #2

READY TO BREW

For ALL functions you must first enter the programming mode.

Turn OFF the power from the Control Panel by pressing .

Press and HOLD and press and RELEASE .

Continue HOLDING until

STOPS blinking and remains on.

ENTER THE PROGRAM MODE #3

READY TO BREW

ENTER THE PROGRAMMING MODE #3

The

will now blink a pattern of flashes from one

to ten. The first blink, if selected = 30 seconds; after that, each blink is one minute.

READY TO BREW