Sony STR-DA5300ES User Manual
79
GB
Ad
v
v
a
nce
d
Spe
ake
rs
Se
tting
Up
quality sound when you do not have a center
speaker connected. Analog downmix works
when you set “Center Mix” to “ON.” This
setting is also effective to input signals from
MULTI CHANNEL INPUT jacks.
speaker connected. Analog downmix works
when you set “Center Mix” to “ON.” This
setting is also effective to input signals from
MULTI CHANNEL INPUT jacks.
x Sur Back Assign
(Settings of the surround back
speaker(s))
speaker(s))
• OFF
If you have not connected surround back
speakers, select “OFF.”
speakers, select “OFF.”
• BI-AMP
If you connect front speakers in a bi-
amplifier configuration, select “BI-AMP.”
amplifier configuration, select “BI-AMP.”
• ZONE 2
If you are using the surround back speakers
in zone 2, select “ZONE 2.” When you select
“ZONE 2,” the input to the SUR BACK
jacks of the MULTI CHANNEL INPUT is
invalid.
in zone 2, select “ZONE 2.” When you select
“ZONE 2,” the input to the SUR BACK
jacks of the MULTI CHANNEL INPUT is
invalid.
Note
Set “Sur Back Assign” to “OFF,” then connect the
surround back speakers to this receiver when you
want to change the connection from a bi-amplifier
connection or a zone 2 connection to a surround
back speakers connection. Re-set up the speakers
after you connect the surround back speakers. Refer
to “Auto Calibration” (page 46) or “Manual Setup”
(page 74).
surround back speakers to this receiver when you
want to change the connection from a bi-amplifier
connection or a zone 2 connection to a surround
back speakers connection. Re-set up the speakers
after you connect the surround back speakers. Refer
to “Auto Calibration” (page 46) or “Manual Setup”
(page 74).
x Crossover Freq
(Speaker crossover frequency)
Lets you set the bass crossover frequency of
speakers that has been set to “SMALL” in the
Speaker menu. Measured speaker crossover
frequency is set for each speaker after the auto
calibration.
The adjusted value is set for each speaker
when you adjust the speaker crossover
frequency using “Crossover Freq” after the
auto calibration.
speakers that has been set to “SMALL” in the
Speaker menu. Measured speaker crossover
frequency is set for each speaker after the auto
calibration.
The adjusted value is set for each speaker
when you adjust the speaker crossover
frequency using “Crossover Freq” after the
auto calibration.
x Multi Ch SW Level
(Multi-channel sub woofer level)
Lets you increase the level of the MULTI
CHANNEL INPUT sub woofer channel signal
by +10 dB. This adjustment may be necessary
CHANNEL INPUT sub woofer channel signal
by +10 dB. This adjustment may be necessary
when connecting a DVD player to the MULTI
CHANNEL INPUT jacks.
The sub woofer level from DVD players is 10
dB lower than that of Super Audio CD players.
CHANNEL INPUT jacks.
The sub woofer level from DVD players is 10
dB lower than that of Super Audio CD players.
x D.Range Comp
(Dynamic range compressor)
Lets you compress the dynamic range of the
soundtrack. This may be useful when you want
to watch movies at low volumes late at night.
Dynamic range compression is possible with
Dolby Digital sources only.
• OFF
soundtrack. This may be useful when you want
to watch movies at low volumes late at night.
Dynamic range compression is possible with
Dolby Digital sources only.
• OFF
The dynamic range is not compressed.
• STD
The dynamic range is compressed as
intended by the recording engineer.
intended by the recording engineer.
• MAX
The dynamic range is compressed
dramatically.
dramatically.
Tips
• Dynamic range compressor lets you compress the
dynamic range of the soundtrack based on the
dynamic range information included in the Dolby
Digital signal.
dynamic range information included in the Dolby
Digital signal.
• “STD” is the standard setting, but it only enacts
light compression. Therefore, we recommend
using the “MAX” setting. This greatly compresses
the dynamic range and lets you view movies late at
night at low volumes. Unlike analog limiters, the
levels are predetermined and provide a very natural
compression.
using the “MAX” setting. This greatly compresses
the dynamic range and lets you view movies late at
night at low volumes. Unlike analog limiters, the
levels are predetermined and provide a very natural
compression.
x Distance Unit (Distance unit)
Lets you select the unit of measure for setting
distances.
• meter
distances.
• meter
The distance is displayed in meters.
• feet
The distance is displayed in feet.