Samsung RF263BE Owner's Manual
10_
setting up
Pull out the freezer drawer (
1.
1 ), then you can
see the lower hinge (
2 ).
Insert the supplied allen wrench (3/16”) (
2.
3 )
into the shaft (
4 ) of the lower hinge.
Please adjust the height by turning the
3.
hex wrench (
3 ) clockwise (
DOWN
) or
counterclockwise (
UP
).
When you turn the hex wrench counter-
clockwise(
clockwise(
), the door will move up.
After adjusting the doors, insert the supplied
4.
fastener (
6 ) using a pliers ( 5 ) in the gap
between the hinge-grommet
( 7 ) and the lower
hinge
( 8 ). The number of fasteners you’ll need
to insert depends on the gap.
2 fastener are enclosed with the refrigerator.
The thickness of each fastener is 0.04”.
The thickness of each fastener is 0.04”.
INSTALLING ThE WATER
DISPENSER LINE
DISPENSER LINE
A water dispenser with a filter is one of the helpful
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
In order for the ice maker to operate properly, a
water pressure of 20~125psi ( 138~862kPa) is
required.
Under normal conditions, a 170 cc (5.75 oz.) cup
can be filled in about 10 seconds.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install
a booster pump to compensate for the low
pressure.
features on your new refrigerator. To help promote
better health, the water filter removes unwanted
particles from your water. However, it does not
sterilize or destroy microorganisms. You may need
to purchase a water purifying system to do that.
In order for the ice maker to operate properly, a
water pressure of 20~125psi ( 138~862kPa) is
required.
Under normal conditions, a 170 cc (5.75 oz.) cup
can be filled in about 10 seconds.
If the refrigerator is installed in an area with low
water pressure (below 20psi), you can install
a booster pump to compensate for the low
pressure.
After you have connected the water line, make
sure the water storage tank inside the refrigerator
is properly filled. To do this, press the water
dispenser lever until the water runs from the water
outlet.
sure the water storage tank inside the refrigerator
is properly filled. To do this, press the water
dispenser lever until the water runs from the water
outlet.
Water line installation kits are available at
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper tubing
and ¼” compression nut.
extra cost from your dealer.
We recommend using a water line
installation kit that contains copper tubing
and ¼” compression nut.
Connecting to the water supply line
First, shut off the main water
1.
supply.
Locate the nearest cold water drinking line and
2.
install the pipe clamp and shut off valve.
Connect the water line installation kit to the
3.
shut off valve.
Connecting the water supply line to
the refrigerator.
the refrigerator.
There are several items that you need to purchase
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
to complete this connection.
You may find these items sold as a kit at your local
hardware store.
use copper tubing
use Plastic tubing
¼” copper tubing
•
¼” compression nut (1pc)
•
Ferrule (2pc)
•
¼” plastic tubing
•
→
Molded end(Bulb)
¼” compression nut (1pc)
•
Pipe clamp
cold water line
Shut off valve
Shut off valve
Pipe clamp
cold water line
Water line installation kit
3
1
2
3
4
DA68-02601A(EN+FR+ES)-0.2.indb 10
2012.3.31 9:49:43 AM