Husqvarna LOGTH2448T User Manual
26
TO REMOVE HOOD AND GRILL AS-
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
SEM BLY
1. Raise hood.
2. Unsnap headlight wire connector.
3. Stand in front of tractor. Grasp hood at
sides, tilt toward engine and lift off of
tractor.
tractor.
4. When replacing hood, be sure to re-
connect the headlight wire con nec tor.
02778
Hood
Headlight Wire
Connector
Connector
ENGINE
TO AD JUST THROTTLE CON TROL
CABLE
The throttle control has been preset at
the factory and ad just ment should not be
necessary Check adjustment as described
below before loosening cable. If adjust-
ment is nec es sary, see engine manual.
TO ADJUST CHOKE CONTROL
The choke control has been preset at
the factory and adjustment should not be
necessary. If adjustment is necessary, see
engine manual.
ADJUST CARBURETOR
Your carburetor has been preset at the
factory and adjustment should not be nec-
essary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load . If the
engine does need adjustment, see engine
manual.
CABLE
The throttle control has been preset at
the factory and ad just ment should not be
necessary Check adjustment as described
below before loosening cable. If adjust-
ment is nec es sary, see engine manual.
TO ADJUST CHOKE CONTROL
The choke control has been preset at
the factory and adjustment should not be
necessary. If adjustment is necessary, see
engine manual.
ADJUST CARBURETOR
Your carburetor has been preset at the
factory and adjustment should not be nec-
essary. However, minor adjustment may
be required to compensate for differences
in fuel, temperature, altitude or load . If the
engine does need adjustment, see engine
manual.
REPLACING BATTERY
WARNING: Do not short battery
ter mi nals by allowing a wrench or any
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci den tal
grounding.
1. Lift hood to raised position.
2. Disconnect BLACK battery cable (A)
other object to contact both terminals at
the same time. Before connecting battery,
remove metal bracelets, wristwatch bands,
rings, etc.
Positive terminal must be connected
fi rst to prevent sparking from ac ci den tal
grounding.
1. Lift hood to raised position.
2. Disconnect BLACK battery cable (A)
then RED battery cable and carefully
remove battery from tractor.
remove battery from tractor.
3. Install new battery with terminals in
same position as old battery.
4. First connect RED battery cable (B) to
positive (+) battery terminal with hex
bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over
terminal.
bolt and keps nut as shown. Tighten
securely. Slide terminal cover (C) over
terminal.
5. Connect BLACK grounding cable to
negative (-) bat tery terminal with re-
main ing hex bolt and keps nut. Tight en
securely
main ing hex bolt and keps nut. Tight en
securely
6. Close hood.
Positive
(Red)
Cable
(Red)
Cable
Negative
(Black)
Cable
(Black)
Cable
02954
A
B
C
TO REPLACE HEADLIGHT BULB
1. Raise hood.
2. Remove bulb hold er from the hole in
1. Raise hood.
2. Remove bulb hold er from the hole in
the back side of the grill.
3. Replace bulb in holder and install bulb
holder securely back into the hole in
the backside of the grill.
the backside of the grill.
4. Close hood.
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
INTERLOCKS AND RELAYS
Loose or damaged wiring may cause
your tractor to run poorly, stop running, or
prevent it from starting.
• Check wiring. See electrical wiring
diagram in the Repair Parts section.
TO REPLACE FUSE
Replace with 30 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.
Replace with 30 amp automotive-type
plug-in fuse. The fuse holder is located
behind the dash.