Roland C-230 User Manual
33
Additional Convenient Functionality <Advanced Operation>
To listen to your new (or a previously recorded) song, proceed as follows:
1.
Press the [PLAY/PAUSE] button (it lights) to start
playback.
playback.
To temporarily stop playback, press [PLAY/PAUSE]
again (the button flashes). Press it again to resume
playback from where you halted it.
again (the button flashes). Press it again to resume
playback from where you halted it.
2.
Press the [STOP] button to stop playback and return to
the beginning of your song.
the beginning of your song.
The recorded song data are transmitted to the C-230’s
MIDI OUT port.
MIDI OUT port.
At first, the C-230 uses a temporary memory for the data you record. That memory is erased when you redo your recording,
load another song or when you switch off the C-230.
load another song or when you switch off the C-230.
Therefore, you need to save recordings you want to keep and play back at a later stage. To this end, the C-230 provides a USB
MEMORY port located next to the PHONES socket (below the left side of the keyboard).
MEMORY port located next to the PHONES socket (below the left side of the keyboard).
The USB MEMORY connector cannot be connected to a
computer.
computer.
1.
Insert the USB flash memory into the USB MEMORY
connector.
connector.
2.
Hold down the [REC] button until the [TRUMPET]
(ENTER) tilt tab starts flashing.
(ENTER) tilt tab starts flashing.
3.
Enter a number between “1” and “99” using the
ORGAN BASS/CLASSIC ORGAN tilt tabs.
ORGAN BASS/CLASSIC ORGAN tilt tabs.
See the numbers BELOW the tilt tabs. To enter “1”, just
press [SUBBASS]. To enter “39”, press [PRINCIPAL] and
[SUPER OCTAVE] (in that order).
If you only press [SUBBASS] (number “1”) at this stage,
for example, the [SUBBASS] and [MIXTUR] tilt tabs flash
to indicate that you selected memory “01”. A similar
flashing pattern is also used for any other number you
select here.
press [SUBBASS]. To enter “39”, press [PRINCIPAL] and
[SUPER OCTAVE] (in that order).
If you only press [SUBBASS] (number “1”) at this stage,
for example, the [SUBBASS] and [MIXTUR] tilt tabs flash
to indicate that you selected memory “01”. A similar
flashing pattern is also used for any other number you
select here.
The C-230 uses the number you selected as file name to
save your song to the USB flash memory. It cannot
display the song numbers that already contain data.
save your song to the USB flash memory. It cannot
display the song numbers that already contain data.
4.
Press the lower part of [TRUMPET] (ENTER) to save
your recording.
your recording.
The C-230 saves the song, and the tilt tabs of the last
configuration you have been using light.
configuration you have been using light.
If the file name with a number you selected already
exists, the [TRUMPET] tilt tab and the [STOP], [PLAY/
PAUSE], and [REC] buttons start flashing. You can
overwrite the “old” song on your USB memory stick by
pressing [TRUMPET] again.
To select a different number, enter it using the Classic
Organ tilt tabs and press [TRUMPET] again.
exists, the [TRUMPET] tilt tab and the [STOP], [PLAY/
PAUSE], and [REC] buttons start flashing. You can
overwrite the “old” song on your USB memory stick by
pressing [TRUMPET] again.
To select a different number, enter it using the Classic
Organ tilt tabs and press [TRUMPET] again.
Never remove the USB memory stick while the C-230 is
saving data.
saving data.
Playing back your recorded song
Saving your song to a USB memory stick
C-230_e.book Page 33 Tuesday, May 19, 2009 10:22 AM