Kingston Technology HyperX 2GB DDR3 Memory Kit KHX16000D3T1K2/2GN Data Sheet
Product codes
KHX16000D3T1K2/2GN
Memory Module Specification
Document No. 4805098-001.C00
11/05/08
KHX16000D3T1K2/2GN
2GB (1GB 128M x 64-Bit x 2 pcs.) PC3-16000
CL9 240-Pin DIMM Kit
Page 1
T E C H N O L O G Y
Keyed
Keyed
Keye
d
DESCRIPTION:
Kingston's KHX16000D3T1K2/2GN is a kit of two 128M x 64-bit 1GB (1024MB) DDR3-2000 CL9 SDRAM
(Synchronous DRAM) "NVIDIA SLI-Ready" memory modules, based on eight 128M x 8-bit DDR3 FBGA components
per module. Each module pair has been tested to run on motherboards that utilize the NVIDIA 790i chipset at DDR3-
2000MHz at a latency timing of 9-9-9-27 at 2.0V. The SPDs are programmed to JEDEC standard latency DDR3-
1066Mhz timing of 7-7-7 at 1.5V. Each 240-pin DIMM uses gold contact fingers and requires +1.5V. The JEDEC
standard electrical and mechanical specifications are as follows:
(Synchronous DRAM) "NVIDIA SLI-Ready" memory modules, based on eight 128M x 8-bit DDR3 FBGA components
per module. Each module pair has been tested to run on motherboards that utilize the NVIDIA 790i chipset at DDR3-
2000MHz at a latency timing of 9-9-9-27 at 2.0V. The SPDs are programmed to JEDEC standard latency DDR3-
1066Mhz timing of 7-7-7 at 1.5V. Each 240-pin DIMM uses gold contact fingers and requires +1.5V. The JEDEC
standard electrical and mechanical specifications are as follows:
FEATURES:
JEDEC standard 1.5V ± 0.075V Power Supply
VDDQ = 1.5V ± 0.075V
533MHz fCK for 1066Mb/sec/pin
8 independent internal bank
Programmable CAS Latency: 6,7,8,9
Posted CAS
Programmable Additive Latency: 0, CL - 2, or CL - 1 clock
Programmable CAS Write Latency(CWL) = 7(DDR3-1066)
8-bit pre-fetch
Burst Length: 8 (Interleave without any limit, sequential with
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or MRS]
starting address “000” only), 4 with tCCD = 4 which does not
allow seamless read or write [either on the fly using A12 or MRS]
Bi-directional Differential Data Strobe
Internal(self) calibration : Internal self calibration through ZQ pin (RZQ : 240 ohm ± 1%)
On Die Termination using ODT pin
Average Refresh Period 7.8us at lower then TCASE 85°C, 3.9us at 85°C < TCASE . 95°C
Asynchronous Reset
PCB : Height 2.401” (61.00mm) w/ heatsink, single sided component
PERFORMANCE:
CL(IDD)
7 cycles
Row Cycle Time (tRCmin)
50.63ns (min.)
Refresh to Active/Refresh Command Time (tRFCmin)
110ns
Row Active Time (tRASmin)
37.5ns (min.)
Power
1.020 W (operating per module)
UL Rating
94 V - 0
Operating Temperature
0
o
C to 85
o
C
Storage Temperature
-55
o
C to +100
o
C