Pioneer DDJ-ERGO User Manual
12
En
Connections
Be sure the power is off when connecting equipment and changing connections.
Be sure to use the USB cable included with this product.
Refer to the operating instructions for the component to be connected.
With this unit, the power is supplied by USB bus power. The unit can be used simply by connecting it to a computer using the USB cable.
! Connect this unit and the computer directly using the included USB cable.
! Connect the computer to which this unit is to be connected to an AC power supply.
! A USB hub cannot be used.
! In cases like the ones below, the power may be insufficient and this unit may not operate on USB bus power.
Be sure to use the USB cable included with this product.
Refer to the operating instructions for the component to be connected.
With this unit, the power is supplied by USB bus power. The unit can be used simply by connecting it to a computer using the USB cable.
! Connect this unit and the computer directly using the included USB cable.
! Connect the computer to which this unit is to be connected to an AC power supply.
! A USB hub cannot be used.
! In cases like the ones below, the power may be insufficient and this unit may not operate on USB bus power.
— When the computer’s USB power supply capacity is insufficient.
— When other USB devices are connected to the computer.
— When headphones with an impedance of less than 32 W are connected.
— When headphones are simultaneously connected to the stereo phone jack and the stereo mini-phone jack.
— When a monaural jack is connected to the [PHONES] terminal.
— When other USB devices are connected to the computer.
— When headphones with an impedance of less than 32 W are connected.
— When headphones are simultaneously connected to the stereo phone jack and the stereo mini-phone jack.
— When a monaural jack is connected to the [PHONES] terminal.
! If this unit cannot be operated on USB bus power, it may operate in the emergency mode (with limited functions).
The following limitations apply in the emergency mode:
— The volume of the headphones will be lower.
— The [DECK] button on the selected deck flashes.
— The volume of the headphones will be lower.
— The [DECK] button on the selected deck flashes.
Names of terminals
Rear panel
MASTER OUT1 (TRS)
R
L
R
L
MASTER OUT2
R
L
AUX IN
MIC
VOL
INPUT SELECT
MIC
VOL
AUX
ON
OFF
USB
4
1
7
2
6
5
3
9
8
a
1
MASTER OUT 1 terminals
Connect powered speakers, etc., here.
This is a TRS phone jack, so both balanced and unbalanced outputs
are supported.
! The sound will be distorted if the level is raised too high when
This is a TRS phone jack, so both balanced and unbalanced outputs
are supported.
! The sound will be distorted if the level is raised too high when
using unbalanced outputs.
2
MASTER OUT 2 terminals
Connect to a power amplifier, etc.
3
MIC terminal
Connects a microphone here.
4
MIC VOL control
Adjusts the audio level input to the [MIC] terminal.
5
AUX/MIC selector switch
Switches the audio input between the external device and the
microphone.
— [AUX]: The external device connected to the [AUX] terminals is
microphone.
— [AUX]: The external device connected to the [AUX] terminals is
selected.
— [MIC]: The microphone connected to the [MIC] terminal is
selected.
! The sound input to the [MIC] and [AUX] terminals is mixed to the
[MASTER OUT] sound.
6
AUX IN VOL control
Adjusts the audio level input to the [AUX IN] terminals.
7
AUX IN terminals
Connect to the output terminal of an external device (sampler, por-
table audio device, etc.)
table audio device, etc.)
8
Kensington security slot
9
ON/OFF switch
Turns this unit’s power on and off.
a
USB terminal
Connects to a computer.
! Connect this unit and the computer directly using the included
! Connect this unit and the computer directly using the included
USB cable.
! A USB hub cannot be used.