Novatel OM-20000041 User Manual
1
Quick Start
MiLLennium GPSCard Software Version 4.50 Command Descriptions Manual Rev 1
19
used to adapt the system to a specific application. Some options apply only to the reference station, while others
apply only to the remote station. Detailed descriptions can be found in Appendix C, Commands Summary.
apply only to the remote station. Detailed descriptions can be found in Appendix C, Commands Summary.
In the following sections, keep the following in mind:
•
Dynamics modes. For reliable performance the antenna should not move more than 1-2
cm when in static mode. See the
cm when in static mode. See the
RTKMODE
commands in Chapter 2, Page 23 and
Appendix C, Page 115 for more information.
•
When using the
FIX
POSITION
command, the height entered must be in metres above mean
sea level; it will be converted to ellipsoidal height inside the receiver. You can enter an
undulation value, if desired, using the
undulation value, if desired, using the
UNDULATION
command; if none is entered, the
receiver estimates an undulation with its internal table. The format of the optional station
ID field depends on whether RTCM or RTCA messages are being used: if RTCM, any
number from 0 - 1023 is valid, while if RTCA, any 4-character string of numbers and
upper-case letters, enclosed in quotation marks, is valid. See Appendix C, Page 98 for
additional information on the station id field.
ID field depends on whether RTCM or RTCA messages are being used: if RTCM, any
number from 0 - 1023 is valid, while if RTCA, any 4-character string of numbers and
upper-case letters, enclosed in quotation marks, is valid. See Appendix C, Page 98 for
additional information on the station id field.
•
The COMn field refers to the serial port (either COM1 or COM2) to which data
communications equipment is connected. The serial port assignment at the reference and
remote stations need not be the same; e.g. a radio transmitter might be connected to
COM1 at the reference station, and a radio receiver to COM2 at the remote station.
remote stations need not be the same; e.g. a radio transmitter might be connected to
COM1 at the reference station, and a radio receiver to COM2 at the remote station.
INITIALIZATION FOR RTCA-FORMAT MESSAGING (RT-2 OR RT-20)
The following commands will enable RTCA-format messaging and allow RT-2 or RT-20 to operate with the
remote station either at rest or in motion. Note that the optional station health field in the existing FIX POSITION
command is not currently implemented in NovAtel’s RTCA messages, though it will be in the future.
remote station either at rest or in motion. Note that the optional station health field in the existing FIX POSITION
command is not currently implemented in NovAtel’s RTCA messages, though it will be in the future.
1. At the reference station:
fix position lat,lon,height,
station id
log com
n,rtcaref,ontime,interval
log com
n,rtcaobs,ontime,interval
Example:
fix position 51.11358042,-114.04358013,1059.4105,”RW34”
log com1,rtcaref,ontime,10
log com1,rtcaobs,ontime,2
2. At the remote station:
accept com
n,rtca
Example:
accept com2,rtca
Congratulations! Your RTK system is now in operation!
INITIALIZATION FOR RTCM59-FORMAT MESSAGING (RT-20 ONLY)
Although RT-20 can operate with either RTCA or RTCM-format messaging, the use of RTCA-format messages is
recommended (see Chapter 4, Page 45 for further information on this topic). Nevertheless, the following
commands will enable RTCM59-format messaging and allow RT-20 to operate with the remote station either at
rest or in motion:
recommended (see Chapter 4, Page 45 for further information on this topic). Nevertheless, the following
commands will enable RTCM59-format messaging and allow RT-20 to operate with the remote station either at
rest or in motion:
1. At the reference station:
fix position lat,lon,height,
station id,station health
log com
n,rtcm3,ontime,interval
log com
n,rtcm59,ontime,interval