Intel Xeon Wolfdale E3210 P4X-UPE3210-316-6M1333 Data Sheet
Product codes
P4X-UPE3210-316-6M1333
Host-Secondary PCI Express* Bridge Registers (D6:F0) (Intel
®
3210 MCH only)
218
Datasheet
8.4
PCISTS1—PCI Status
B/D/F/Type:
0/6/0/PCI
Address Offset: 6–7h
Default Value:
0010h
Access:
RO, RWC
Size:
16 bits
This register reports the occurrence of error conditions associated with primary side of
the "virtual" Host-PCI Express bridge embedded within the MCH.
Bit
Access
Default
Value
Description
15
RO
0b
Detected Parity Error (DPE): Not Applicable or Implemented. Hardwired to 0.
Parity (generating poisoned Transaction Layer Packets) is not supported on the
primary side of this device.
Parity (generating poisoned Transaction Layer Packets) is not supported on the
primary side of this device.
14
RWC
0b
Signaled System Error (SSE): This bit is set when this Device sends a SERR
due to detecting an ERR_FATAL or ERR_NONFATAL condition and the SERR
Enable bit in the Command register is 1. Both received (if enabled by
BCTRL1[1]) and internally detected error messages do not affect this field).
due to detecting an ERR_FATAL or ERR_NONFATAL condition and the SERR
Enable bit in the Command register is 1. Both received (if enabled by
BCTRL1[1]) and internally detected error messages do not affect this field).
13
RO
0b
Received Master Abort Status (RMAS): Not Applicable or Implemented.
Hardwired to 0. The concept of a master abort does not exist on primary side of
this device.
Hardwired to 0. The concept of a master abort does not exist on primary side of
this device.
12
RO
0b
Received Target Abort Status (RTAS): Not Applicable or Implemented.
Hardwired to 0. The concept of a target abort does not exist on primary side of
this device.
Hardwired to 0. The concept of a target abort does not exist on primary side of
this device.
11
RO
0b
Signaled Target Abort Status (STAS): Not Applicable or Implemented.
Hardwired to 0. The concept of a target abort does not exist on primary side of
this device.
Hardwired to 0. The concept of a target abort does not exist on primary side of
this device.
10:9
RO
00b
DEVSELB Timing (DEVT): This device is not the subtractively decoded device
on bus 0. This bit field is therefore hardwired to 00 to indicate that the device
uses the fastest possible decode.
on bus 0. This bit field is therefore hardwired to 00 to indicate that the device
uses the fastest possible decode.
8
RO
0b
Master Data Parity Error (PMDPE): Because the primary side of the PCI
Express's virtual peer-to-peer bridge is integrated with the MCH functionality,
there is no scenario where this bit will get set. Because hardware will never set
this bit, it is impossible for software to have an opportunity to clear this bit or
otherwise test that it is implemented. The PCI specification defines it as a R/WC,
but for our implementation an RO definition behaves the same way and will meet
all Microsoft testing requirements.
This bit can only be set when the Parity Error Enable bit in the PCI Command
register is set.
Express's virtual peer-to-peer bridge is integrated with the MCH functionality,
there is no scenario where this bit will get set. Because hardware will never set
this bit, it is impossible for software to have an opportunity to clear this bit or
otherwise test that it is implemented. The PCI specification defines it as a R/WC,
but for our implementation an RO definition behaves the same way and will meet
all Microsoft testing requirements.
This bit can only be set when the Parity Error Enable bit in the PCI Command
register is set.
7
RO
0b
Fast Back-to-Back (FB2B): Not Applicable or Implemented. Hardwired to 0.
6
RO
0b
Reserved
5
RO
0b
66/60MHz capability (CAP66): Not Applicable or Implemented. Hardwired to
0.
0.
4
RO
1b
Capabilities List (CAPL): Indicates that a capabilities list is present. Hardwired
to 1.
to 1.
3
RO
0b
INTA Status (INTAS): Indicates that an interrupt message is pending
internally to the device. Only PME sources feed into this status bit (not PCI INTA-
INTD assert and deassert messages). The INTA Assertion Disable bit,
PCICMD1[10], has no effect on this bit.
internally to the device. Only PME sources feed into this status bit (not PCI INTA-
INTD assert and deassert messages). The INTA Assertion Disable bit,
PCICMD1[10], has no effect on this bit.
2:0
RO
000b
Reserved