Rocketfish RF-RBKIT Leaflet

 RF-RBKIT Wireless HD Audio Starter Kit

QUICK SETUP GUIDE

11

1   Standby LED 

2   Power/Join button 

3   Power/Join indicator

4   BASS button  

5   Bass indicator

6   SOURCE indicator 

7   SOURCE button

8   HD indicator 

1   Standby LED 

2   Power/Join button 

3   Power/Join indicator

4   HD A indicator 

5   HD A button 

6   Source A button 

7   Source A/B LED indicator

8   Source B button 

 IR remote 

DC adapter 

(for sender)

AC power cable

(for receiver)

 

Speaker cable,

 

3 ft (x4)

Cable spool 

 (for receiver)

The sender and receiver packaged together were pre-joined at the factory, so if you are only using one 

sender and receiver set, no further configuration is needed. If an active link is established between them, 

the Power/Join indicators on both units will light steadily (no blink). If your sender and receiver are 

your User Guide for more information. Make sure the Source A or B LED is illuminated on the sender for the 

channel that you have connected to your network for the audio transmission to be active.

Press the SOURCE button on the receiver until the audio channel you desire is playing. 

Adjust the volume as desired.

11

12

13

14

15

16

9   HD B button 

10 HD B indicator

11  DC IN jack 

12  SPEAKER IN A jacks

13  Pre-in A/B jack 

14  SPEAKER IN B jacks

15  Hub Enable switch 

16  4 -Channel Lock

 

switch

12

13

14

9   IR sensor 

10 VOLUME knob 

11 Removable cable spool slot

12 AC IN jack

13 Removable cable spool slot (line level) 

14 SPEAKER OUT jacks 

Connect the right surround speaker terminals of your amplifier 

to the right speaker terminals of the sender by connecting the 

red speaker wire to the red (+) terminals, and the black 

speaker wire to the black (-) terminals. Repeat to connect the 

left surround speaker terminals.
Connecting to an external audio source 

Connect external audio source(s) to the Pre-in A and/or B jacks 

on the rear of sender using the 3.5 mm male-to-male stereo 

cable and the 3.5 mm female-to -RCA stereo cable.

Note: The Input A/Input B buttons on the remote control allow 

you to select between the Speaker in or Pre in (line level). Each 

press of the button will toggle to the other source. The unit 

must be powered up for these buttons to operate and the 

state when powered down will be remembered.

Connect the right surround speaker 

to the right speaker terminals on the 

receiver. Use a red speaker wire to 

connect the red (+) terminals and a 

black speaker wire to connect the 

black (-) terminals.

Repeat this step to connect the left 

surround speaker.

09-0474

QUICK SE

TUP GUIDE

3.5 mm male-to-male 

stereo cable,

 

3ft (x2)

3.5 mm female-to-RCA 

stereo cable, 

6 in

.

 (x2)

1

5

4

10

8

7

2 3

9

6

Wireless sender

Wireless receiver

9

10

1

2 3

5

4

8

7

6

TM

TM

TM

TM

To activate the battery: Remove the tab from the bottom of the 

remote control to enable the battery.

Every Rocketboost network must contain at least one hub device, which directs network data traffic 

and helps devices join the network. The network can have only one hub, which can be enabled by 

using the hub switch on the back of all Rocketboost transmitters. The sender in this kit is set at the

factory for hub mode and the receiver has been pre-joined to this sender at the factory for easy

setup. If you have an existing Rocketboost network, the sender's hub mode switch should 

be set to Disable. The sender and receiver also need to be joined to your existing hub device 

(the one with the green power LED).

See your User Guide for instructions on joining devices to the network.  

TM

TM