American Standard 0955.023 Leaflet

J61

© 2008 AS America Inc.

 146mm

(5-3/4)

   41mm
   (1-5/8)

425mm

(16-3/4)

127mm

(5)

  216mm

(8-1/2)

203mm
(8)

*

216mm

(8-1/2)

FINISHED

FLOOR

SIDE PROFILE

(ADA)

1-1/4 O.D. 

TAILPIECE

 

C/L OF SUPPLIES

   AS REQUIRED

C/L OF (2) 13mm(1/2) DIA.
KNEE CONTACT GUARD
ANCHOR HOLES

13mm(1/2) DIA.
ANCHOR SCREW 
HOLES

C/L OF 1-1/4
O.D. WASTE

C/L OF 16mm X 29mm
(5/8 X 1-1/8) ANCHOR
SLOTS

C/L OF 54mm(2-1/8 DIA.)

 HOLES FOR 

CONCEALED ARMS

197mm

(7-3/4)

102mm

(4)

152mm

(6)

102mm

(4)

83mm

(3-1/4)

(4) 25mm (1") DIA.

ACCESS HOLES

FOR CONC. ARMS

102mm
(4)

540mm

(21-1/4)

559mm

(22)

864mm

(34)

(FRONT

RIM)

743mm

(29-1/4)

254mm

(10) REF.

FINISHED

WALL

FINISHED

WALL

(2) 16mm (5/8") DIA.

ACCESS HOLES

FOR CONC. ARMS

406mm

(16)

REF.

*

267mm

(10-1/2)

165mm

(6-1/2)

89mm

(3-1/2)

44mm

(1-3/4)

MURRO™ UNIVERSAL DESIGN 
WALL-HUNG LAVATORY
 
•  Vitreous china
•  Rear overflow
•  Recessed self-draining deck
•  For concealed arm or wall support
•  Shown with optional vitreous china shroud/
  knee contact guard 0059.020 available

❏

 

0954.000 Faucet holes on 102mm (4") Ctrs

    (Illustrated)

❏

 

0954.023 Faucet holes on 102mm (4") Ctrs   

    • Extra right-hand hole

❏

 

0954.021 Faucet holes on 102mm (4") Ctrs   

    • Extra left-hand hole

❏

 

0958.000 Faucet holes on 203mm (8") Ctrs

❏

 

0955.000 Center hole only

❏

 

0955.023 Center hole

    • Extra right-hand hole

❏

 

0955.021 Center hole

    • Extra left-hand hole
 
Nominal Dimensions:  
559mm (22") deep, 540mm (21-1/4") wide

Bowl sizes:
394mm (15-1/2") wide, 343mm (13-1/2") 
front to back, 127mm (5") deep

❏

 

    (Vitreous China) (Must be specified separately)

Compliance Certifications -
Meets or Exceeds the Following Specifications:
• ASME A112.19.2 for Vitreous China Fixtures

To Be Specified:
❏

Color:   ❏  White   ❏  Bone  ❏  Silver   

❏

  Optional Vitreous China Shroud/Knee

  Contact guard: 0059.020
❏

  Faucet*:

❏

  Faucet Finish: 

❏

Supplies:

❏

1-1/4" Trap:

❏

  Nipple:

* See faucet section for additional models available

For Universal Design Options, top of rim may be mounted 

at 813mm (32") from finished floor to meet ADA and ANSI 

A117.1 requirements. Check local codes.

MEETS THE AMERICANS WITH DISABILITIES ACT GUIDE-
LINES AND ANSI A117.1 ACCESSIBLE AND USABLE
BUILDINGS AND FACILITIES - CHECK LOCAL CODES.
Top of front rim mounted 864mm (34") from finished floor.

●

LOOSE KEY ANGLE STOPS, LESS WALL ESCUTCHEONS. SUPPLIES 

REQUIRED.

* 

DIMENSIONS SHOWN FOR LOCATION OF SUPPLIES AND “P" TRAP ARE 

SUGGESTED.

SHROUD/KNEE CONTACT GUARD 0059.020 NOT INCLUDED AND MUST BE 

ORDERED SEPARATELY.

■

 SUITABLE FOR REINFORCEMENT ONLY, ACTUAL DIMENSIONS MUST 

BE TAKEN FROM FIXTURE.

FITTINGS NOT INCLUDED AND MUST BE ORDERED SEPARATELY.

PROVIDE SUITABLE REINFORCEMENT FOR ALL WALL SUPPORTS.

INSTALLATION INSTRUCTIONS SUPPLIED WITH LAVATORY.

IMPORTANT:  Dimensions of fixtures are nominal and may vary within the 

range of tolerances established by ANSI Standard A112.19.2.

These measurements are subject to change or cancellation. No responsibility  

is assumed for use of superseded or voided pages.

SEE REVERSE FOR ADDITIONAL ROUGHING-IN 
DIMENSIONS

Revised 5/06