Philips RAMA FRESNEL & PC RANGE User Manual
Version 5: September 2010 © Philips Selecon All Rights Reserved
RAMA FRESNEL & PC RANGE
OPERATION MANUAL
THANK YOU FOR PURCHASING A PHILIPS SELECON LUMINAIRE. WE HAVE DESIGNED THIS
LUMINAIRE TO PROVIDE YOU WITH A SUPERIOR FITTING IN PERFORMANCE, DESIGN AND
ENGINEERING. WE ARE CONFIDENT THAT IT WILL PERFORM TO YOUR EXPECTATIONS FOR MANY
YEARS TO COME.
IMPORTANT NOTE:
Before discarding the packaging ensure you have the suspension bolt set, colour frame, lamp base
spacers &/or the lamp.
Before operating your new luminaire please read this information to assist you in making maximum use
of your luminaire, its maintenance and care. If you would like further assistance contact your Philips
Selecon dealer or Philips Selecon.
LAMPING YOUR LUMINAIRE
Before lamping
of your luminaire, its maintenance and care. If you would like further assistance contact your Philips
Selecon dealer or Philips Selecon.
LAMPING YOUR LUMINAIRE
Before lamping
– DISCONNECT THE LUMINAIRE FROM THE POWER SUPPLY. Be aware also that the
lamp, luminaire or integrated safety bond may still be hot, so exercise the necessary caution to avoid
burns. These luminaires are not suitable for mounting on a normally flammable surface.
The Philips Selecon Rama range comprises four models: the High Performance
175 Fresnel, High Performance 175 PC, 150 Fresnel and 150 PC. The Philips
Selecon Rama range is designed for use with either the T/29 1200W or T/19 1000W
lamp.
Philips Selecon Rama Fresnel and PC with GX9.5 Lampbase
To facilitate the use of these two lamps which are of different sizes the height of the
GX9.5 lamp base plate is adjustable. The adjustment is by means of positioning 2
lamp base spacers under the lamp base. Without the spacers, the lamp base is
aligned for use with the T/29 1200W lamp.
burns. These luminaires are not suitable for mounting on a normally flammable surface.
The Philips Selecon Rama range comprises four models: the High Performance
175 Fresnel, High Performance 175 PC, 150 Fresnel and 150 PC. The Philips
Selecon Rama range is designed for use with either the T/29 1200W or T/19 1000W
lamp.
Philips Selecon Rama Fresnel and PC with GX9.5 Lampbase
To facilitate the use of these two lamps which are of different sizes the height of the
GX9.5 lamp base plate is adjustable. The adjustment is by means of positioning 2
lamp base spacers under the lamp base. Without the spacers, the lamp base is
aligned for use with the T/29 1200W lamp.
With the spacers, the lamp base is aligned for use with the 1000W lamp. To make
the adjustment, loosen the two lamp base fastening screws with a screwdriver, and
lift the lamp base up. Slide the two lamp base spacers into place around the lamp base screws, and tighten the
screws. Lamps able to be used in the Rama GX9.5 version are: 1200W
the adjustment, loosen the two lamp base fastening screws with a screwdriver, and
lift the lamp base up. Slide the two lamp base spacers into place around the lamp base screws, and tighten the
screws. Lamps able to be used in the Rama GX9.5 version are: 1200W
– T/29: 1000W – T/11, T/19, CP24,
CP70.
Philips Selecon Rama Fresnel and PC with G22 Lampbase
It is not necessary to adjust the lamp base height with the G22 version of the Rama range. Lamps able to be
used in the Rama G22 version are: CP71
– 1000W. To fit the lamp:
Release the clip fastener and swing down the rear door.
Insert lamp taking care not to touch the quartz envelope with your fingers.
Close door and lock off the fastener.