Sony UNIMDB3 User Manual
UNI- X X X 7 X X X
Pendant Dome Housing Model Naming Convention
I for indoor
O for outdoor
O for outdoor
N for normal type
R for vandal resistant
P for pressurized
R for vandal resistant
P for pressurized
L for Long – RX550N, RZ25N
S for Short – RZ30N, RZ50N
S for Short – RZ30N, RZ50N
C for clear
T for tinted
T for tinted
1 for DC12V
2 for AC24V
3 for no interface wiring
2 for AC24V
3 for no interface wiring
or electronics
W for wireless
7” diameter dome
Example: UNI-ONL7C2
Outdoor (with heater/blower), normal type, for RZ25N, RX530N, RX550N or RX570N, 7” diameter, clear dome, AC24V feed
11
SNC RX Series / SNC-RZ25N
SNC-RZ50N / SNC-RZ30N
Normal
Vandal Resistant
Pressurized
Normal
Vandal Resistant
Pressurized
Outdoor
housing for pan/tilt/
zoom network camera, pendant
mount type, w/ heater & blower.
AC 24V interface, AC 24V power
supply NOT included.
mount type, w/ heater & blower.
AC 24V interface, AC 24V power
supply NOT included.
Clear Dome
UNI-ONL7C2
UNI-ORL7C2
UNI-OPL7C2
UNI-ONS7C1
UNI-ORS7C1
UNI-OPS7C1
Tinted Dome
UNI-ONL7T2
UNI-ORL7T2
UNI-OPL7T2
UNI-ONS7T1
UNI-ORS7T1
UNI-OPS7T1
Wireless Ready Outdoor
housings for pendant mount type,
w/ heater & blower. Prewired
internally for use with SNCA-CFW1.
Dome has N-type connector
interface on the top to accept
external antenna. External antenna &
mount NOT included. AC 24V feed,
AC 24V power supply NOT included.
w/ heater & blower. Prewired
internally for use with SNCA-CFW1.
Dome has N-type connector
interface on the top to accept
external antenna. External antenna &
mount NOT included. AC 24V feed,
AC 24V power supply NOT included.
Clear Dome
UNI-ONL7C2W
UNI-ORL7C2W
–
UNI-ONS7C1W
UNI-ORS7C1W
–
Tinted Dome
UNI-ONL7T2W
UNI-ORL7T2W
–
UNI-ONS7T1W
UNI-ORS7T1W
–
Indoor Long
housing for
pan/tilt/zoom network camera,
pendant mount type, no heater/
blower or interface wiring included.
pendant mount type, no heater/
blower or interface wiring included.
Clear Dome
UNI-INL7C2
UNI-IRL7C2
–
–
–
–
Tinted Dome
UNI-INL7T2
UNI-IRL7T2
–
–
–
–
Indoor Short
housing, pendant
mount type, no heater/blower,
internal AC 24V to DC-12V for
camera feed, AC 24V external
interface wiring included, AC 24V
power supply NOT included.
internal AC 24V to DC-12V for
camera feed, AC 24V external
interface wiring included, AC 24V
power supply NOT included.
Clear Dome
–
–
–
UNI-INS7C1
UNI-INS7C3
UNI-RS7C1
–
Tinted Dome
–
–
–
UNI-INS7T1
UNI-INS7T3
UNI-RS7T1
–
W
IR
E
LE
S
S
Recessed Ceiling Housing
SNC-CS50N, SNC-Z20N, SNC-CS10,
SNC-CS11, SNC-CM120, SNC-CS20
SNC-CS11, SNC-CM120, SNC-CS20
Outdoor
Indoor (no heater/blower)
SNC-UNIHB/1
SNC-UNI
Housing with Wall Bracket
10
Housing Selection Guide
Recessed Ceiling Housing for Fixed Cameras
Architectural / Engineering Specifications
UNI-PBU1 Bid Specifications
The power box shall be a Sony Model UNI-PBU1 or equivalent.The power input shall be a 120vac or 220vac and the output 24vac, rated at 84va (watts).The product includes PTC fuses
for the camera power and another one for the heater/blower power. It shall be designed to support one outdoor Sony housing with heaters, blowers and camera.The body of the unit
shall be cast aluminum with white power coat finish. (2) ¾” conduit inputs located at the bottom of the box to provide input for power and for data cabling.The unit shall be designed for
outdoor locations, with an IP 66 rating. Clips shall be provided to allow it to be mounted to the pole mount adapter UNI-PMA1, or the corner mount adapter, UNI-CMA1. Mechanical
Specifications: Dimensions – 7.9” (w) x 8.8” (h) x 3.8” (d). Weight – 9 lbs. Construction – Cast Aluminum.
The power box shall be a Sony Model UNI-PBU1 or equivalent.The power input shall be a 120vac or 220vac and the output 24vac, rated at 84va (watts).The product includes PTC fuses
for the camera power and another one for the heater/blower power. It shall be designed to support one outdoor Sony housing with heaters, blowers and camera.The body of the unit
shall be cast aluminum with white power coat finish. (2) ¾” conduit inputs located at the bottom of the box to provide input for power and for data cabling.The unit shall be designed for
outdoor locations, with an IP 66 rating. Clips shall be provided to allow it to be mounted to the pole mount adapter UNI-PMA1, or the corner mount adapter, UNI-CMA1. Mechanical
Specifications: Dimensions – 7.9” (w) x 8.8” (h) x 3.8” (d). Weight – 9 lbs. Construction – Cast Aluminum.
UNI-MDB2/3 Bid Specifications
The wall/pendant mount adaptor shall be a Sony model UNI-MDB2, UNI-MDB3 or equivalent.The UNI-MDB2 shall support the SNC-DF80N, SNC-DF85N, SSC-CD77 and SSC-CD75 cameras.
The UNI-MDB3 shall support the SNC-DM160 and SNC-DS60.
The wall/pendant mount adaptor shall be a Sony model UNI-MDB2, UNI-MDB3 or equivalent.The UNI-MDB2 shall support the SNC-DF80N, SNC-DF85N, SSC-CD77 and SSC-CD75 cameras.
The UNI-MDB3 shall support the SNC-DM160 and SNC-DS60.
The cast aluminum top cover shall have screw taps to allow the cameras to be mounted directly, and provide a 1” NPT pipe
thread for mounting to a pipe or to the included wall mount bracket.The wall mount is also constructed from aluminum.The kit shall allow the camera to be mounted down from the ceil-
ing using a 1” threaded pipe (not provided) or to be mounted to an interior or exterior wall.The bracket features a light gray finish.The wall mount can be combined with the UNI-CMA1
for corner mount applications and with the UNI-PMA1 for pole mount applications.The kit shall include gaskets and Teflon tape for water ingress protection outdoors. Mechanical
Specifications: UNI-MDB2 Dimensions - 7.28” diameter x 2.78” UNI-MDB3 Dimensions - 6.82” diameter x 2.83” Weight – UNI-MDB2 and UNI-MDB3 – 2 lbs.; gooseneck bracket – 0.9 lb
ing using a 1” threaded pipe (not provided) or to be mounted to an interior or exterior wall.The bracket features a light gray finish.The wall mount can be combined with the UNI-CMA1
for corner mount applications and with the UNI-PMA1 for pole mount applications.The kit shall include gaskets and Teflon tape for water ingress protection outdoors. Mechanical
Specifications: UNI-MDB2 Dimensions - 7.28” diameter x 2.78” UNI-MDB3 Dimensions - 6.82” diameter x 2.83” Weight – UNI-MDB2 and UNI-MDB3 – 2 lbs.; gooseneck bracket – 0.9 lb
UNI-IFF7 Recessed Series Bid Specifications
The recessed ceiling housing designed & engineered for Sony’s fixed cameras (SNC-CS50N, SNC-Z20N, SNC-CS20, SNC-CS11 and SNC-CS10) shall be the Model UNI-IFF7C3 and UNI-IFF7T3
or equivalent.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below the ceiling.The steel top shall measure 5.5”
(h) x 11” (d).The lower injection molded polycarbonate dome shall be available in clear or tinted material.The UNI-IFF7T3 shall include a tinted lower dome and the UNI-IFF7C3, a clear
lower dome.The lower dome shall be made from injection molded polycarbonate, and held in place by a 19-gauge steel trim ring with a white powdercoat finish.The product shall be
designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material thickness. Mechanical Specifications (all
models): Dimensions –12” (w) x 9.1” (h) x 12” (d). Weight – approx. 9 lbs. (without camera).
The recessed ceiling housing designed & engineered for Sony’s fixed cameras (SNC-CS50N, SNC-Z20N, SNC-CS20, SNC-CS11 and SNC-CS10) shall be the Model UNI-IFF7C3 and UNI-IFF7T3
or equivalent.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below the ceiling.The steel top shall measure 5.5”
(h) x 11” (d).The lower injection molded polycarbonate dome shall be available in clear or tinted material.The UNI-IFF7T3 shall include a tinted lower dome and the UNI-IFF7C3, a clear
lower dome.The lower dome shall be made from injection molded polycarbonate, and held in place by a 19-gauge steel trim ring with a white powdercoat finish.The product shall be
designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material thickness. Mechanical Specifications (all
models): Dimensions –12” (w) x 9.1” (h) x 12” (d). Weight – approx. 9 lbs. (without camera).
UNI-ID7 Recessed Series Bid Specifications
The recessed ceiling housing shall be for Sony’s Pan/Tilt/Zoom camera models, SNC-RX series, SNC-RZ25N, SNC-RZ50N and the SNC-RZ30N.The UNI-ID7C3 shall include a clear lower
dome and the UNI-ID7T3 shall include a tinted lower dome.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below
the ceiling.The steel top shall measure 5.5” (h) x 11” (d). The lower dome shall be made from injection molded polycarbonate, and held in place by a 19-gauge steel trim ring with a
white powdercoat finish.The product shall be designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material
thickness. Mechanical Specifications (all models): Dimensions –12” (w) x 9.1” (h) x 12” (d). Weight – approx 9 lbs. (without camera).
The recessed ceiling housing shall be for Sony’s Pan/Tilt/Zoom camera models, SNC-RX series, SNC-RZ25N, SNC-RZ50N and the SNC-RZ30N.The UNI-ID7C3 shall include a clear lower
dome and the UNI-ID7T3 shall include a tinted lower dome.The back box shall be constructed from 18 and 20-gauge steel and be capable of being installed in its entirety from below
the ceiling.The steel top shall measure 5.5” (h) x 11” (d). The lower dome shall be made from injection molded polycarbonate, and held in place by a 19-gauge steel trim ring with a
white powdercoat finish.The product shall be designed to be installed in either sheetrock or drop ceilings.Three rotating support arms shall allow for adjustment to the ceiling material
thickness. Mechanical Specifications (all models): Dimensions –12” (w) x 9.1” (h) x 12” (d). Weight – approx 9 lbs. (without camera).
SNC-UNI Series Bid Specifications
The SNCUNIHB/1 & SNCUNI environmental housings shall be constructed from two extruded aluminum (.08” wall thickness, white finish) halves and two injection molded polycarbonate
end caps. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal.The top of the housing shall be hinged from
the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the alu-
minum camera sled. Maximum camera/lens combined length shall not exceed 10-1/2 inches. A 25 VA heater is mounted to the inside of the bottom extrusion, directly behind the view-
ing window, for defogging and deicing on the SNCUNIHB/1 model. Four vent plugs (2 in front, 2 in rear) will create a positive airflow (front to rear) when the blower is in use (SNCUNIHB/1
model).Two watertight strain relief plugs will be located at the rear of the housing for separate communication wiring and power cable entry. Mechanical Specifcations: Dimensions –
5.7”(w) x 5.4”(h) x 15.25”(d) including protruding parts, not including wall mount bracket. Weight: approx 8 pounds (without camera, with heater and blower).
The SNCUNIHB/1 & SNCUNI environmental housings shall be constructed from two extruded aluminum (.08” wall thickness, white finish) halves and two injection molded polycarbonate
end caps. A clear polycarbonate viewing window shall be ultrasonically welded to the inside of the front end cap, creating a watertight seal.The top of the housing shall be hinged from
the side to allow accessibility to the camera by one screw in each end cap. Camera adjustment or removal shall be provided via one screw located in the key hole slot on the alu-
minum camera sled. Maximum camera/lens combined length shall not exceed 10-1/2 inches. A 25 VA heater is mounted to the inside of the bottom extrusion, directly behind the view-
ing window, for defogging and deicing on the SNCUNIHB/1 model. Four vent plugs (2 in front, 2 in rear) will create a positive airflow (front to rear) when the blower is in use (SNCUNIHB/1
model).Two watertight strain relief plugs will be located at the rear of the housing for separate communication wiring and power cable entry. Mechanical Specifcations: Dimensions –
5.7”(w) x 5.4”(h) x 15.25”(d) including protruding parts, not including wall mount bracket. Weight: approx 8 pounds (without camera, with heater and blower).
Standard Indoor and Outdoor housings,“N”Type
The outdoor dome camera housing shall be a Sony Model UNI-ONL7C2, UNI-ONL7C2W, UNI-ONS7C1, UNI-ONS7C1W or equivalent.The indoor models shall be a Sony Model UNI-INL7C2,
UNI-INS7C1, UNI-INS7C3 or equivalent.The UNI-ONL7C2, UNI-ONL7C2W, and UNI-INL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ONS7C1, UNI-
ONS7C1W, UNI-INS7C1 and UNI-INS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The products hous-
ing shall be manufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0.The dome shall be made of an injection molded, optically clear, polycar-
bonate blend material.The dome shall be held in place with minimum of (3) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the enclosure
shall be from below with (3) captive fasteners used to press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through
the top of the housing on all models.The engineered plastic top, with its reflective white paint, insulates internal equipment. A wall mount bracket, Sony model UNI-WMB1, shall be avail-
able as an option.The outdoor models shall also be equipped with 24vac input blower and thermostatically controlled heater.The blower shall draw 1W continuous power.The 25W
heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C). UNI-ONS7C1, UNI-ONS7C1W and UNI-INS7C1
will include a 24vac to 12vdc power supply built into the housing.The UNI-INS7C3 shall not include any electronics, and installer provided 12vdc power, must be supplied to the housing.
UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable with an MMCX connector for the optional wireless LAN
card, and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted models shall be Model UNI-ONL7T2, UNI-ONL7T2W, UNI-ONS7T1, UNI-ONS7T1W. Indoor tinted
models shall be UNI-INL7T2, UNI-INS7T1, UNI-INS7T3. Mechanical Specifications: UNI-ONL models – Dimensions : 10.3” (D) x 10.3” (w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ONS
models - Dimensions : 10.3” (D) x 10.3” (w) x 13.3” (H). Weight- 7 Lbs (without camera).
The outdoor dome camera housing shall be a Sony Model UNI-ONL7C2, UNI-ONL7C2W, UNI-ONS7C1, UNI-ONS7C1W or equivalent.The indoor models shall be a Sony Model UNI-INL7C2,
UNI-INS7C1, UNI-INS7C3 or equivalent.The UNI-ONL7C2, UNI-ONL7C2W, and UNI-INL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ONS7C1, UNI-
ONS7C1W, UNI-INS7C1 and UNI-INS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The products hous-
ing shall be manufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0.The dome shall be made of an injection molded, optically clear, polycar-
bonate blend material.The dome shall be held in place with minimum of (3) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the enclosure
shall be from below with (3) captive fasteners used to press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through
the top of the housing on all models.The engineered plastic top, with its reflective white paint, insulates internal equipment. A wall mount bracket, Sony model UNI-WMB1, shall be avail-
able as an option.The outdoor models shall also be equipped with 24vac input blower and thermostatically controlled heater.The blower shall draw 1W continuous power.The 25W
heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C). UNI-ONS7C1, UNI-ONS7C1W and UNI-INS7C1
will include a 24vac to 12vdc power supply built into the housing.The UNI-INS7C3 shall not include any electronics, and installer provided 12vdc power, must be supplied to the housing.
UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable with an MMCX connector for the optional wireless LAN
card, and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted models shall be Model UNI-ONL7T2, UNI-ONL7T2W, UNI-ONS7T1, UNI-ONS7T1W. Indoor tinted
models shall be UNI-INL7T2, UNI-INS7T1, UNI-INS7T3. Mechanical Specifications: UNI-ONL models – Dimensions : 10.3” (D) x 10.3” (w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ONS
models - Dimensions : 10.3” (D) x 10.3” (w) x 13.3” (H). Weight- 7 Lbs (without camera).
Vandal Resistant Indoor and Outdoor housings,“R”Type
The vandal resistant outdoor dome camera housing shall be a Sony Model UNI-ORL7C2, UNI-ORL7C2W, UNI-ORS7C1, UNI-ORS7C1W or equivalent.The indoor models shall be a Sony
Model UNI-IRL7C2, UNI-IRL7C3 or equivalent.The UNI-ORL7C2, UNI-ORL7C2W, and UNI-IRL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ORS7C1,
UNI-ORS7C1W, and UNI-IRS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing top and pen-
dant mount bracket shall be manufactured from durable cast aluminum.The dome shall be made of an injection molded, optically clear, polycarbonate blend material.The dome shall
be held in place with minimum of (3) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the enclosure shall be from below with (3) captive fas-
teners. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models. A wall mount bracket, Sony model UNI-WMB1, shall
be available as an option.The outdoor models shall also be equipped with 24vac input blowers and thermostatically controlled heaters.The blower shall draw 2W continuous power.The
50W heaters shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).The UNI-ORS7C1 and UNI-ORS7C1W
will include a 24vac to 12vdc power supply built into the housing. The UNI-IRS7C3 shall not include any electronics, and an installer provided 12vdc power, must be supplied to the hous-
ing. UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable.The product shall have a pre-installed wireless
antenna cable with an MMCX connector for the optional wireless card, and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted lower dome models shall
be the UNI-ORL7T2, UNI-ORL7T2W, UNI-ORS7T1, UNI-ORS7T1W. Indoor tinted models shall be the UNI-IRL7T2, UNI-IRL7T3. Mechanical Specifications: UNI-ORL models – Dimensions: 10.3” (D) x
10.3” (w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ORS models – Dimensions: 10.3” (D) x 10.3” (w) x 13.3” (H). Weight- 7 Lbs (without camera).
The vandal resistant outdoor dome camera housing shall be a Sony Model UNI-ORL7C2, UNI-ORL7C2W, UNI-ORS7C1, UNI-ORS7C1W or equivalent.The indoor models shall be a Sony
Model UNI-IRL7C2, UNI-IRL7C3 or equivalent.The UNI-ORL7C2, UNI-ORL7C2W, and UNI-IRL7C2 housings shall be designed for the SNC-RX series and SNC-RZ25N cameras.The UNI-ORS7C1,
UNI-ORS7C1W, and UNI-IRS7C3 housings shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing top and pen-
dant mount bracket shall be manufactured from durable cast aluminum.The dome shall be made of an injection molded, optically clear, polycarbonate blend material.The dome shall
be held in place with minimum of (3) fasteners, and a safety cable shall be provided to hold the dome while servicing. Access to the enclosure shall be from below with (3) captive fas-
teners. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models. A wall mount bracket, Sony model UNI-WMB1, shall
be available as an option.The outdoor models shall also be equipped with 24vac input blowers and thermostatically controlled heaters.The blower shall draw 2W continuous power.The
50W heaters shall turn on at 60°F (15°C) and turn off at 80°F (25°C).The housing shall support a temperature range of -20°F (-29°C) to 122°F (50°C).The UNI-ORS7C1 and UNI-ORS7C1W
will include a 24vac to 12vdc power supply built into the housing. The UNI-IRS7C3 shall not include any electronics, and an installer provided 12vdc power, must be supplied to the hous-
ing. UNI-ONL7C2W and UNI-ONS7C1W are wireless ready dome housings.The product shall have a pre-installed wireless antenna cable.The product shall have a pre-installed wireless
antenna cable with an MMCX connector for the optional wireless card, and an N type connector on the enclosure top, for an external antenna. Outdoor Tinted lower dome models shall
be the UNI-ORL7T2, UNI-ORL7T2W, UNI-ORS7T1, UNI-ORS7T1W. Indoor tinted models shall be the UNI-IRL7T2, UNI-IRL7T3. Mechanical Specifications: UNI-ORL models – Dimensions: 10.3” (D) x
10.3” (w) x 14.6” (H). Weight- 7 Lbs (without camera). UNI-ORS models – Dimensions: 10.3” (D) x 10.3” (w) x 13.3” (H). Weight- 7 Lbs (without camera).
Pressurized Outdoor housings,“P”Type
The pressurized outdoor dome camera housing shall be a Sony Model UNI-OPL7C2, UNI-OPS7C1 or equivalent.The UNI-OPL7C2 housing shall be designed for the SNC-RX series and SNC-
RZ25N cameras.The UNI-OPS7C1 housing shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing shall be man-
ufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0.The dome shall be made of an injection molded, optically clear, polycarbonate blend
material, and shall be held in place with (9) captive fasteners, used to press the dome against the sealing O-ring. A secondary O-ring seal shall be provided at the top of the enclosure
through a precision machined bracket.This machined bracket shall also be provided with a 5 to 7 psi pressure-relief valve and a standard bore thread dill valve to insert inert dry nitro-
gen into the enclosure. All incoming wires will enter the unit via a 10-pin hermetically sealed connector. Access to the enclosure shall be from below with (9) captive fasteners used to
press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models. The engineered
plastic top, with its reflective white paint, insulates internal equipment. A wall mount bracket, Sony model UNI-WMB1, shall be available as an option.The housing shall be equipped with
24VAC input blowers and thermostatically controlled heaters.The blowers shall draw 2W continuous power. UNI-OPS7C1 shall include a 24vac to 12vdc power supply built into the hous-
ing. The 50W heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C). The housing shall support a temperature range of -40°F (-40°C) to 122°F (50°C). Tinted lower dome models
shall be UNI-OPL7T2, UNI-OPS7T1. Mechanical Specifications:“P” type models- 14.4” (H) x 11.2” (w) x 11.2” (D). Weight- 8 Lbs (without camera).
The pressurized outdoor dome camera housing shall be a Sony Model UNI-OPL7C2, UNI-OPS7C1 or equivalent.The UNI-OPL7C2 housing shall be designed for the SNC-RX series and SNC-
RZ25N cameras.The UNI-OPS7C1 housing shall be designed for the SNC-RZ50 and SNC-RZ30 cameras.The product shall come standard with a pendant mount.The housing shall be man-
ufactured from a high-impact engineered plastic, UV protected, with a UL flame rating of 94V0.The dome shall be made of an injection molded, optically clear, polycarbonate blend
material, and shall be held in place with (9) captive fasteners, used to press the dome against the sealing O-ring. A secondary O-ring seal shall be provided at the top of the enclosure
through a precision machined bracket.This machined bracket shall also be provided with a 5 to 7 psi pressure-relief valve and a standard bore thread dill valve to insert inert dry nitro-
gen into the enclosure. All incoming wires will enter the unit via a 10-pin hermetically sealed connector. Access to the enclosure shall be from below with (9) captive fasteners used to
press the dome against a sealing O-ring. A twist-off feature shall allow for the final removal of the dome.The wiring enters through the top of the housing on all models. The engineered
plastic top, with its reflective white paint, insulates internal equipment. A wall mount bracket, Sony model UNI-WMB1, shall be available as an option.The housing shall be equipped with
24VAC input blowers and thermostatically controlled heaters.The blowers shall draw 2W continuous power. UNI-OPS7C1 shall include a 24vac to 12vdc power supply built into the hous-
ing. The 50W heater shall turn on at 60°F (15°C) and turn off at 80°F (25°C). The housing shall support a temperature range of -40°F (-40°C) to 122°F (50°C). Tinted lower dome models
shall be UNI-OPL7T2, UNI-OPS7T1. Mechanical Specifications:“P” type models- 14.4” (H) x 11.2” (w) x 11.2” (D). Weight- 8 Lbs (without camera).
SNC-CS50N, SNC-Z20N, SNC-CS11, SNC-CS10, SNC-CM120, SNC-CS20
Clear
Tinted
UNI-IFF7C3
UNI-IFF7T3
SNC RX Series, SNC-RZ50N, SNC-RZ25N, SNC-RZ30N, SNC-RZ50N
Clear
Tinted
SNC ID7C1
SNC-ID7T1