Philips CMD305A/05 Quick Setup Guide
Bluetooth V2.1 or later
Quick start guide
Краткое руководство
www.philips.com/welcome
Always there to help you
CMD305A
Register your product and get support at
Question?
Contact
Philips
All registered and unregistered trademarks are property of
their respective owners.
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
© 2013 Koninklijke Philips Electronics N.V.
All rights reserved.
CMD305A_05_QSG_V2.0
EN
Congratulations on your purchase, and welcome to Philips! To
fully benefi t from the support that Philips offers, register your
product at www.philips.com/welcome.
Read and understand all instructions before you use
this product. If damage is caused by failure to follow the
instructions, the warranty does not apply.
fully benefi t from the support that Philips offers, register your
product at www.philips.com/welcome.
Read and understand all instructions before you use
this product. If damage is caused by failure to follow the
instructions, the warranty does not apply.
1
What’s in the box (Fig. 1)
1 Main unit and front panel
(with a sleeve)
2 Trim plate
3 ISO standard connector
4 Rubber cushion
5 1 x Screw
6 2 x Disassembly tools
7 USB cable
8 User manual
9 Quick start guide
5 REAR LINE OUT R
(Socket)
Rear right speaker
6 OE REMOTE (Brown)
OE remote
7 FRONT LINE OUT L
Front left speaker
8 FRONT LINE OUT R
Front right speaker
Tip
•
The pin arrangement for the ISO connectors depends on the type of vehicle
you drive. Be sure to make proper connections to prevent damage to the
system.
you drive. Be sure to make proper connections to prevent damage to the
system.
Mount into the dashboard (Fig. 3)
If the car does not have an on-board drive or navigation
computer, disconnect the negative terminal of the car battery.
computer, disconnect the negative terminal of the car battery.
•
If you disconnect the car battery in a car that has an on-board drive
or navigation computer, the computer may lose its memory.
or navigation computer, the computer may lose its memory.
•
If the car battery is not disconnected, to avoid short-circuit, make
sure that the bare wires do not touch each other.
sure that the bare wires do not touch each other.
1
Make sure that the car dashboard opening is within the
indicated measurements. (Fig. 3 - 1)
2
Install the sleeve into the dashboard and bend the tabs
outwards to fi x the sleeve. (Fig. 3 - 2)
Note
•
If the system is not fi xed by sleeve but by the supplied screws,
skip this step.
skip this step.
3
Place the supplied rubber cushion over the end of the
mounting bolt. (Fig. 3 - 3)
4
Slide the system into the dashboard until you hear a “click”.
(Fig. 3 - 4)
5
Attach the trim plate. (Fig. 3 - 5)
6
Reconnect the negative terminal of the car battery.
3 Power
on
Press
.
»
[WELCOME] scrolls.
•
To power off the system, press and hold
until [GOODBYE] is
displayed.
4
Set the clock
1
Press and hold to access the system menu.
2
Press repeatedly until [CLOCK] and the current time are
displayed.
»
If the clock is not set before, [--:--] is displayed.
3
Rotate
to set the hour.
4
Press
to confi rm.
5
Rotate
to set the minute.
6
Press
to confi rm.
2
Press a numeric key to select a preset station.
7
Play from a USB storage device
(Fig. 5)
This system can play .mp3 and .wma fi les that are copied onto
a compatible USB storage device.
a compatible USB storage device.
Note
•
Philips does not guarantee compatibility with all USB storage
devices.
devices.
•
NTFS (New Technology File System) fi le system is not supported.
1
Connect the USB storage device to the socket.
2
Press
repeatedly until [USB] is displayed.
»
Play starts automatically.
If play does not start automatically,
1
1
Press /
to select a folder.
2
Press
/
to select a fi le.
3
Press
to start play.
8
Listen to an external device (Fig.
6)
9
Use Bluetooth devices (Fig. 7)
With this car audio system, you can listen to audio from a
player or make a call through Bluetooth.
player or make a call through Bluetooth.
Pair a device
Note
•
Philips does not guarantee the compatibility with all Bluetooth
devices.
devices.
•
Before pairing a device with this system, read its user manual for
Bluetooth compatibility. Make sure that the Bluetooth fi rmware
version of the device is V2.1 or later.
Bluetooth compatibility. Make sure that the Bluetooth fi rmware
version of the device is V2.1 or later.
•
Make sure that Bluetooth function is enabled on your device, and
your device is set as visible to all other Bluetooth devices.
your device is set as visible to all other Bluetooth devices.
•
The operational range between this system and a Bluetooth
device is approximately 3 meters (10 feet).
device is approximately 3 meters (10 feet).
•
Any obstacle between this system and a Bluetooth device can
reduce the operational range.
reduce the operational range.
•
Keep away from any other electronic device that may cause
interference.
interference.
On your device, follow the steps below.
1
Enable it to search for other Bluetooth devices.
2
In the device list, select CMD305A .
3
Enter the default password “ 0000 “.
»
If the pairing is successful, [PAIR OK] is displayed.
2 Installation
Connect wires (Fig. 2)
Caution
•
Make sure that all loose leads are insulated with electrical tape.
1
Check the car’s wiring carefully, and then connect them to
the supplied ISO wires. (Fig. 2 - 1)
Connector
Connect
to
1 Yellow wire
The +12V car battery which is live at all
times
times
2 Blue/White
wire
The electric antenna control lead or power
supply lead of the antenna booster. If there is
no electric antenna or antenna booster, or it
is manually operated telescopic antenna, it is
unnecessary to connect this lead.
supply lead of the antenna booster. If there is
no electric antenna or antenna booster, or it
is manually operated telescopic antenna, it is
unnecessary to connect this lead.
3 Black wire
A metal surface of the car. Connect the
black ground (earth) lead before connecting
the yellow and red power supply leads.
black ground (earth) lead before connecting
the yellow and red power supply leads.
4 Red wire
The +12V power terminal which is live in
the accessory (ACC) position of the ignition
switch. If there is no accessory position,
connect to the +12V car battery terminal
that is always live. Make sure that the black
ground (earth) lead is connected to a metal
surface of the car fi rst.
the accessory (ACC) position of the ignition
switch. If there is no accessory position,
connect to the +12V car battery terminal
that is always live. Make sure that the black
ground (earth) lead is connected to a metal
surface of the car fi rst.
5 Green and
green/black
wires
wires
Left speaker (rear)
6 White and
white/black
wires
wires
Left speaker (front)
7 Gray and
gray/black
wires
wires
Right speaker (front)
8 Purple and
purple/black
wires
wires
Right speaker (rear)
2
Connect the other end of the supplied standard connector
to the car audio system. (Fig. 2 - 2)
Connector
Connect
to
1 ANTENNA
Antenna for radio
2 External Mic
An external microphone for
phone call
phone call
3 SUBWOOFER (Socket) Subwoofer
4 REAR LINE OUT L
4 REAR LINE OUT L
(Socket)
Rear left speaker
5
Select a source (Fig. 4)
Press
repeatedly to select a source.
•
[RADIO] : FM/MW radio
•
[AUDIO-IN] : the audio that is transferred through the AUDIO-IN
socket
socket
•
[BT AUDIO] : the audio that is transferred from a Bluetooth device
•
[USB] : When a USB storage device is connected and recognized, you
can select this source to play audio fi les that are stored on it.
can select this source to play audio fi les that are stored on it.
6
Listen to radio
Select a radio region
You can select a radio region that matches your location.
1
Press and hold to access the system menu.
2
Press repeatedly until [AREA] is displayed.
3
Rotate
to select an option.
•
[USA] (United States)
•
[EUR] (Western Europe)
•
[RUS] (Russia)
•
[AUS] (Australia)
•
[EAS] (Middle East)
•
[ASI] (Asia Pacifi c)
•
[JAP] (Japan)
•
[LAT] (Latin America)
Tune to a radio station
1
Press
repeatedly to switch the source to [RADIO] .
2
Press repeatedly to select a band: [FM1] , [FM2] , [FM3] ,
[MW1] , or [MW2] .
3
Press and hold or until the frequency digits blink.
4
Press or repeatedly to tune to a radio station
manually.
»
The radio station is broadcast.
•
To search for a radio station automatically, press
or
.
Store stations automatically
1
Press and hold to access the system menu.
2
Press repeatedly until [STORE >] is displayed.
3
Press
to confi rm.
»
The strongest stations of the selected band are saved in preset
channels automatically.
channels automatically.
Note
•
You can store a maximum of six stations in each band.
Tune to a preset station
1
Press repeatedly to select a band.
Play audio from a connected device
If the connected Bluetooth device supports Advanced Audio
Distribution Profi le (A2DP), you can listen to tracks that are
stored on the device through the system. If the device also
supports Audio Video Remote Control Profi le (AVRCP)
profi le, you can control play on the system.
Distribution Profi le (A2DP), you can listen to tracks that are
stored on the device through the system. If the device also
supports Audio Video Remote Control Profi le (AVRCP)
profi le, you can control play on the system.
1
Connect the Bluetooth device to this system via Bluetooth.
2
Press
repeatedly to switch the source to [BT AUDIO] .
»
Play starts automatically.
•
If play does not start, press
.
•
To pause play, press
again.
•
To skip to the previous or next track, press
/
.
Note
•
If the connected device does not support the AVRCP profi le,
control play on the connected device.
control play on the connected device.
Make a call
Note
•
Keep the Bluetooth connection active between the system and
your mobile.
your mobile.
Functions
Actions
Call a number Dial the number on your mobile and send the
call.
Redial the last
called number
called number
1
Press .
»
[Redial] is displayed.
2
Press
to confi rm.
»
[CALL---] is displayed.
Pick up an
incoming call
incoming call
Press to answer the call.
Reject an
incoming call
incoming call
Press and hold until [END] is displayed.
End a call
Press .
Transfer a
phone call to
mobile
phone call to
mobile
Press and hold until [TRANSFER] is
displayed.
displayed.
»
The loudspeakers are muted, and the voice comes
from your mobile only.
from your mobile only.
10 Use the dock
An application Philips CarStudio is available on Google Play
Store for this car audio system. To enjoy full features, download
and install the application to your Android-powered phone.
Store for this car audio system. To enjoy full features, download
and install the application to your Android-powered phone.
CMD305A_05_QSG_V2.0.indd 1
CMD305A_05_QSG_V2.0.indd 1
1/4/2013 2:42:58 PM
1/4/2013 2:42:58 PM