JVC GR-DVM5 User Guide
78
EN
CONTROLS, INDICATIONS AND CONNECTORS
(Cont.)
1
DC charger (
Z
pg. 10)
Attach the battery pack to charge.
2
Camcorder attachment part (
Z
pg. 58)
Attach the camcorder to this part when charging
the battery installed in the camcorder or when
editing.
the battery installed in the camcorder or when
editing.
3
Multi connector (
Z
pg. 58)
The AC Charger Station can be connected with
this camcorder through this connector. Never
touch it with your hand or hit it with a hard
object; if the pins are damaged, the connectors
will become unusable due to contact failure.
this camcorder through this connector. Never
touch it with your hand or hit it with a hard
object; if the pins are damaged, the connectors
will become unusable due to contact failure.
4
EDIT connector (
Z
pg. 65)
Using an editing cable, connect to the remote
control or VCR.
control or VCR.
5
JLIP (Joint Level Interface Protocol)
connector
connector
Connect to a JLIP-compatible camcorder or VCR
to control it from the computer using JLIP Player
Pack (optional) etc.
NOTE:
to control it from the computer using JLIP Player
Pack (optional) etc.
NOTE:
Make sure that the camcorder is turned on while
connecting the camcorder to a PC using the AC Charger
Station’s JLIP connector. If the camcorder is turned off
(because the Power Dial is set to “OFF” or due to Auto
Shut Off* etc.) while the JLIP program software is used,
it will be impossible to control the connected devices
from the computer. In such a case, first try turning the
camcorder on again, or unplug the JLIP connection
cable from the AC Charger Station’s JLIP connector.
Then, initialize or run the software again.
* Auto Shut Off:
connecting the camcorder to a PC using the AC Charger
Station’s JLIP connector. If the camcorder is turned off
(because the Power Dial is set to “OFF” or due to Auto
Shut Off* etc.) while the JLIP program software is used,
it will be impossible to control the connected devices
from the computer. In such a case, first try turning the
camcorder on again, or unplug the JLIP connection
cable from the AC Charger Station’s JLIP connector.
Then, initialize or run the software again.
* Auto Shut Off:
If 5 minutes elapse in the Record-Standby mode or in
the Pause mode, the camcorder’s power shuts off
automatically to conserve energy.
the Pause mode, the camcorder’s power shuts off
automatically to conserve energy.
6
S-VIDEO OUT connector (
Z
pg. 58, 65)
• Outputs S-Video signal.
• Connect to a video unit equipped with an S-
• Connect to a video unit equipped with an S-
Video connector.
7
VIDEO OUT connector (
Z
pg. 58, 65)
Connect to a TV or VCR using the VIDEO cable
(provided).
(provided).
8
AUDIO OUT connector [L/R]
(
(
Z
pg. 58, 65)
Connect to a TV or VCR using the Audio cable(s)
(provided).
(provided).
9
DC OUT jack (
Z
pg. 12)
Connect the DC cord (provided) and plug it into
the camcorder.
the camcorder.
0
Lock lever (with release button)
(
(
Z
pg. 58)
Slide the lock lever in the direction of the arrow
to connect to the camcorder. To detach the
camcorder, press the release button and slide the
lock lever in the opposite direction of the arrow.
to connect to the camcorder. To detach the
camcorder, press the release button and slide the
lock lever in the opposite direction of the arrow.
!
Charger Indicator (for camcorder or
battery) (
battery) (
Z
pg. 10, 59)
Blinks during charging. When charging is
finished, this indicator stops blinking and stays
lit. When the camcorder is turned on, charging
is interrupted.
finished, this indicator stops blinking and stays
lit. When the camcorder is turned on, charging
is interrupted.
@
Power lamp
3
2
1
9
8
7
5 6
4
!
0
@
AC Charger Station