Philips 37 User Manual
10
English
General Information
Supplied accessories
– 2 speaker boxes including 2 speaker cables
– remote control and two AA batteries
– AM loop antenna
– FM wire antenna
– AC power cord
– remote control and two AA batteries
– AM loop antenna
– FM wire antenna
– AC power cord
Environmental Information
All unnecessar y packaging has been omitted. We
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
have tried to make the packaging easy to
separate into three materials: cardboard (box),
polystyrene foam (buffer) and polyethylene (bags,
protective foam sheet).
Your system consists of materials which can be
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
recycled and reused if disassembled by a
specialized company. Please observe the local
regulations regarding the disposal of packaging
materials, exhausted batteries and old
equipment.
Safety Information
●
Place the system on a flat, hard and stable
surface.
surface.
●
Place the system in a location with adequate
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
ventilation to prevent internal heat build-up in
your system. Allow at least 10 cm (4 inches)
clearance from the rear and the top of the unit
and 5 cm (2 inches) from each side.
●
The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
covering the ventilation openings with items,
such as newspapers, table-cloths, curtains, etc.
●
Do not expose the system, batteries or discs to
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
excessive moisture, rain, sand or heat sources
caused by heating equipment or direct sunlight.
●
No naked flame sources, such as lighted candles,
should be placed on the apparatus.
should be placed on the apparatus.
●
No objects filled with liquids, such as vases, shall
be placed on the apparatus.
be placed on the apparatus.
●
If the system is brought directly from a cold to a
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the system. Should this occur, the CD
player would not operate normally. Leave the
power on for about one hour with no disc in the
system until normal playback is possible.
warm location, or is placed in a very damp room,
moisture may condense on the lens of the disc
unit inside the system. Should this occur, the CD
player would not operate normally. Leave the
power on for about one hour with no disc in the
system until normal playback is possible.
●
The mechanical parts of the set contain self-
lubricating bearings and must not be oiled or
lubricated.
lubricating bearings and must not be oiled or
lubricated.
●
When the system is switched to Standby
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.
mode, it is still consuming some power.
To disconnect the system from the
power supply completely, remove the AC
power plug from the wall socket.
The set complies with the FCC-Rules,
Part 15 and with RSS-210 of Industry
Canada.
Part 15 and with RSS-210 of Industry
Canada.
Operation is subject
to the following two conditions:
1. this device may not cause harmful
interference, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
to the following two conditions:
1. this device may not cause harmful
interference, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
The set complies with the FDA/DHHS Rule
21 CFR Subchapter J in effect at Date of
Manufacture
21 CFR Subchapter J in effect at Date of
Manufacture
001-036_MCM760_37_Eng
2/16/2006, 20:11
10