TELEDEX L2-10E User Guide

Included with the Diamond+L2 are (one each):

• Base unit

• Coiled handset cord

• User guide

• Handset

• Clear plastic overlay

• Line cord

Contact your supplier or Teledex for information on ordering

custom designed and printed faceplates to enhance the look of your

Teledex Diamond+L2 telephone.

1) Located on the left side of the Diamond+L2 is a modular jack

labeled

Insert one end of the coiled handset cord

into this jack. (You should hear the coil cord click when proper-

ly inserted).

2) Insert the other end of the coiled handset cord into the modular

jack on the handset.

3) Turn the telephone so the back panel is facing you. Insert either

end of the line cord into the jack on the back of the telephone

this jack is labeled

4) Insert the other end of the line cord into a telephone wall outlet jack.

5) Once your telephone is connected, place the paper faceplate over

the keys. The plastic overlay slips into place by hooking the tabs

on the overlay into the recessed slots located on both sides. The

overlay is easiest to insert when; the left or right side tabs are

inserted first, and the middle part of the overlay is slightly bowed

to allow for insertion of the other tabs.

or 

is selected by depressing one of the latching line

keys. The line key that is depressed is the active line when using the

handset. Pressing the alternate line key will make the other line

active. Use the 

key to place callers on hold while connecting

to the other line.

1) Press the line key associated with the ringing line. A red flashing

LED indicates which line is ringing.

2) Lift the handset to connect to the ringing line.

3) To end the call, hang up by replacing the handset.

1) Select Line 1 or Line 2 (if not previously selected).

2) Lift the handset. The line LED will turn green indicating line 

in use.

3) Listen for dial tone, dial the desired number, or press the 

key to automatically dial a number.

4) To end the call, hang up by replacing the handset.

To place a call on Hold for Line 1 or Line 2:

1) Press the red 

key. The Line LED will change to red and 

the Line key will de-latch. The handset can be replaced without

disconnecting the call.

The raised red lens is a Message Waiting light. Some telephone systems

permit an operator or message center to turn on the red Message

Waiting light to alert you that you have a message waiting.

Additionally, the Message Waiting light will act as a visual ring indica-

tor, flashing when the telephone is ringing.

The Diamond+L2 has two ring volume settings. 

To change the ring volume: 

Locate the adjustment control on the back of the telephone

labeled 

. There are two controls (labeled L1 for

Line 1 and L2 for Line 2). Slide the switch to the desired LOW or HI

ring volume for each line.

The DATA PORT is a modular jack, located on the right side of the

telephone, labeled 

. You can connect a facsimile, modem,

answering machine, and other devices to Line 2 through the DATA

PORT. (Line 1 can be used for voice calls and Line 2 can be used for

data calls simultaneously).

To use the DATA PORT: 

Insert the modular line cord from your facsimile machine, modem,

etc., into the jack labeled 

. The DATA PORT will only access

Line 2. When using the telephone for voice communications and

data communications at the same time, use Line1 for your voice

communications.

To Redial the last telephone number dialed:

1) Press 

or 

to select a line.

2) Lift the handset (go off hook).

3) Press the 

key. The Diamond+L2 will dial the last number

dialed.

The Diamond+L2 Handset Volume Boost will increase the handset

volume. Pressing the 

button during a call will

increase the receive volume, pressing the key again will return the

volume to the normal level. The handset volume is reset to normal

with each new call.

The Diamond+L2 has 1 programmable 

key. This key can

be programmed to automatically dial a telephone number or, activate

a telephone system feature. The AUTO DIAL location may have been

pre-programmed before installation.

The phone must be connected to a telephone line.

1) Lift the handset.

2) Press the recessed 

key and release it (please see diagram

on back page for key location).

3) Enter the telephone number including PAUSE* as required. You

can enter up to 15 digits.

4) Press the 

key where the number is to be stored.

5) Hang up the handset.

*A 3.6 second pause is entered in a dialing sequence by pressing the

key for each PAUSE required.

The following procedure should be followed with all Teledex 

telephone products prior to sending the telephone to the factory 

for repair.

1) Please perform the tests listed below:

a.  Test the telephone on a different telephone jack.

b.  Test telephone with a different line cord.

c.  Test with a different handset cord (coiled cord).

d.  For two line products, please ensure that one of the line 

buttons is pressed (if both line buttons are in the UP position,

the telephone will not operate).

2) If the steps listed above do not provide a remedy for the suspect

telephone, please place a tag on the individual telephone 

describing the defect. Next, call the Teledex Repair Department

at 1 (800) 875-8539 for an RMA number. You must have an

RMA number to return products to Teledex.

3) Kindly note: An RMA number is unique to each return

shipment. Do not duplicate this number on any future shipments.

SHIPPING INSTRUCTIONS:

Please print the RMA number clearly on the outside of your shipping

carton(s). Please ship to the following address:

Teledex LLC / RMA#___________

6311 San Ignacio Avenue, San Jose, CA 95119

FREIGHT CHARGES:

The Customer is responsible for shipping products for repair to

Teledex. After repair, Teledex will return telephone products to the

Customer freight prepaid in the same manner in which is was sent

(i.e. Freight sent to Teledex UPS Blue, will be returned via 2 day ship-

ping).

**Please note: When telephones are returned for repair due to misuse

(i.e. liquid spills, abuse, or Customer modification - warranty label

broken), the Customer will be charged the standard repair fee, regard-

less of warranty status.