Bosch she43p22uc User Guide
17
8
Operating the Dishwasher
FOR TOP CONTROLS
(Top controls are dishwashers with a hidden fascia panel.
Please refer to the introduction page of this manual for
examples).
(Top controls are dishwashers with a hidden fascia panel.
Please refer to the introduction page of this manual for
examples).
To start the dishwasher:
•
•
Open the door.
•
Press the ON/OFF button.
•
Select a cycle and desired options.
•
Close the door.
To Interrupt a cycle:
•
•
Open the dishwasher door just far enough to expose
the control panel.
the control panel.
•
Press the ON/OFF button to turn the unit of.
•
Wait at least 10 seconds before opening the
dishwasher door.
dishwasher door.
•
To resume the cycle, press the ON/OFF button and
close the dishwasher door.
close the dishwasher door.
FOR FRONT CONTROLS
(Front controls are dishwashers with an exposed fascia
panel. Please refer to the introduction page of this manu-
al for examples).
(Front controls are dishwashers with an exposed fascia
panel. Please refer to the introduction page of this manu-
al for examples).
To start the dishwasher:
•
•
Press the ON/OFF button.
•
Select a cycle and desired options.
To Interrupt a cycle:
•
•
Press the ON/OFF button to turn the unit of.
•
Wait at least 10 seconds before opening the
dishwasher door.
dishwasher door.
•
To resume the cycle, press the ON/OFF button and
close the dishwasher door.
close the dishwasher door.
NOTE: Should you need to interrupt a cycle (to add or
remove an item, to add detergent, etc.), it is best to do so
within the irst 30 minutes of the cycle.
remove an item, to add detergent, etc.), it is best to do so
within the irst 30 minutes of the cycle.
You could be seriously scalded if you allow hot water
to splash out of the dishwasher. OPEN THE DOOR
CAREFULLY during any wash or rinse cycle. Do not
to splash out of the dishwasher. OPEN THE DOOR
CAREFULLY during any wash or rinse cycle. Do not
fully open the door until water noises have stopped.
WARNING
Canceling or changing a cycle
To cancel or change a cycle, open the dishwasher door
far enough to expose the control buttons then press and
hold the “Cancel/Reset” buttons for 3 seconds.
To cancel or change a cycle, open the dishwasher door
far enough to expose the control buttons then press and
hold the “Cancel/Reset” buttons for 3 seconds.
Close the door and wait until the dishwasher completes
the cycle (approx. 1 min). Open the door and press the
ON/OFF button. You may now begin a new cycle.
the cycle (approx. 1 min). Open the door and press the
ON/OFF button. You may now begin a new cycle.
Cancel / Reset
Dishware Drying
At the end of the cycle the dishwasher will stop and a
period of condensation drying will follow. After drying,
the cycle is complete and depending on your model:
•
At the end of the cycle the dishwasher will stop and a
period of condensation drying will follow. After drying,
the cycle is complete and depending on your model:
•
the “Clean” light will illuminate OR
•
the cycle completion signal will sound OR
•
the countdown display will show "0" OR
•
The InfoLight
™ will turn of.
•
When the cycles are complete, the “Sanitized”
indicator (select models) on your dishwasher control
panel will illuminate. However, if your household
water supply is too hot, your dishwasher’s heating
time may be reduced, and the Sanitized indicator
may not illuminate.
indicator (select models) on your dishwasher control
panel will illuminate. However, if your household
water supply is too hot, your dishwasher’s heating
time may be reduced, and the Sanitized indicator
may not illuminate.