DIESEL dz1067 User Guide
IMPORTANT TO KNOW!
• When the watch is underwater or wet, never use the pushers/bezels, or set the time. Watch cases and metal bracelets should be rinsed thoroughly in fresh water after being in salt water.
• No hot tub/sauna. Please do not take your DIESEL watch into the hot tub/sauna. The combination of extreme heat and water may cause your watch to lose some of its water-resistance.
• No backward hand, or date, adjustments should be made when the analog hands read between 8pm and 3am. At these times, the gears are too close together and such a change could
• No hot tub/sauna. Please do not take your DIESEL watch into the hot tub/sauna. The combination of extreme heat and water may cause your watch to lose some of its water-resistance.
• No backward hand, or date, adjustments should be made when the analog hands read between 8pm and 3am. At these times, the gears are too close together and such a change could
cause damage.
• Tighten screwlock crown completely.
• Always set the crown in the normal position.
• Always set the crown in the normal position.
RESISTANCE TO WATER
Depth
WATER-RESISTANT 3 BAR (30 M)
WATER-RESISTANT 5 BAR (50 M)
WATER-RESISTANT 10 BAR (100 M)
Caseback marking
3 ATM
5 ATM
10 ATM
Light spray, perspiration, light rain, etc.
OK
OK
OK
Bathing, etc.
NO
OK
OK
Swimming, etc.
NO
NO
OK
Skin diving (diving without oxygen cylinder)
NO
NO
OK
Water-resistant characteristics
Normal daily water contact.
Suitable for bathing, but cannot be worn for swimming or diving.
Suitable for skin diving.
Automatic Winding Movements
A timepiece with an automatic winding movement obtains the power to wind itself by the movement of your wrist, there is no battery. Therefore, not wearing the timepiece for several consecutive days
could exhaust the power reserve. If your watch stops, it is recommended that you manually wind the movement by rotating the crown clockwise to achieve the necessary power reserve.
could exhaust the power reserve. If your watch stops, it is recommended that you manually wind the movement by rotating the crown clockwise to achieve the necessary power reserve.
It is important that your timepiece is adjusted to match the size of your wrist. A loose fit may result in a loss in capacity of the timepiece to wind itself. When fully wound, your timepiece has a power
reserve of approximately 38 hours.
reserve of approximately 38 hours.
Automatic 6T51
1. To start time-keeping, rotate the crown clockwise 15-20 times in position 1.
2. Pull crown out to position 2 and rotate clockwise to set time. Push crown back to position 1.
3. Pull crown out to position 2. Then pull crown out from position 2 to position 3 to advance date by one day. Each time the
2. Pull crown out to position 2 and rotate clockwise to set time. Push crown back to position 1.
3. Pull crown out to position 2. Then pull crown out from position 2 to position 3 to advance date by one day. Each time the
crown is pulled from position 2 to position 3 the date is advanced by one increment. Return crown to position 1.
(1) (2) (3)
DATE
TV Automatic Movement
WINDING
With the crown in the position 1, turn the crown 15-20 times and the movement will start after shaking the watch slightly.
After approximately 40-42 hours, the timepiece will need to be wound.
After approximately 40-42 hours, the timepiece will need to be wound.
SETTING THE TIME
1. Pull crown out to position 2.
2. Turn crown to set hour and minute hands.
3. Push crown back to position 1.
2. Turn crown to set hour and minute hands.
3. Push crown back to position 1.
SETTING THE DATE
1. Pull the crown to position 2.
2. Pull the crown from position 2 to position 3, then date advance one day.
3. After the date has been set, push the crown back to position 1.
2. Pull the crown from position 2 to position 3, then date advance one day.
3. After the date has been set, push the crown back to position 1.
(1) (2) (3)
DATE
MINUTE HAND
SECOND HAND
HOUR HAND
Automatic Winding Movement 8215
WINDING
With the crown in the position 1, turn the crown 15-20 times and the movement will start after shaking the watch slightly.
After approximately 40-42 hours, the timepiece will need to be wound.
After approximately 40-42 hours, the timepiece will need to be wound.
SETTING THE TIME
1. Pull the crown out to position 3.
2. Turn the crown to set the hour and minute hands.
3. Push the crown back to position 1.
2. Turn the crown to set the hour and minute hands.
3. Push the crown back to position 1.
SETTING THE DATE
1. Pull the crown out to position 2.
2. Turn the crown counter-clockwise to set the date.
3. Push the crown back to the position 1.
2. Turn the crown counter-clockwise to set the date.
3. Push the crown back to the position 1.
(1) (2) (3)
DATE
MINUTE HAND
SECOND HAND
HOUR HAND