Manualsbrain.com
  1. Manuals
  2. Brands
  3. Mitsubishi
  4. es200u
  5. User Manual

Mitsubishi es200u User Manual

Download
Page of 49
EN-24
Correcting keystone
Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs 
when the projector is not perpendicular to the screen. 
To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of 
these steps.
•
Using the remote control
Press  /  on the projector or remote control to display the Keystone 
correction page. Press   to correct keystoning at the top of the image. Press 
 to correct keystoning at the bottom of the image.
•
Using the OSD menu
1.
Press MENU/EXIT and then press 
/
 until the DISPLAY menu is 
highlighted.
2.
Press   to highlight Keystone and press MODE/ENTER. The 
Keystone correction page is displayed.
3.
 Press   to correct keystoning at the top of the image or press   to 
correct keystoning at the bottom of the image.
•
You can correct the vertical keystones. However, their adjustment ranges are 
limited in such correction.
•
When the keystone adjustment is carried out, the adjustment value is indicated. 
Note that this value doesn’t mean a projection angle. 
•
The allowable range of the adjustment value in the keystone adjustment varies depending on the installation conditions. 
•
Images may not be projected in a shape of a regular rectangle or with its aspect ratio 4:3, depending on the installation 
conditions of the projector and the screen. 
•
When the keystone adjustment takes effect, the resolution decreases. In addition, stripes may appear or straight lines may 
bend in images with complicated patterns. They are not due to product malfunctions. 
•
Noise may appear on the screen during the keystone adjustment because of the type of the video signal being projected 
and the setting values of the keystone adjustment. In such cases, set the keystone adjustment values in the range where 
the image is displayed without noise. 
•
When the keystone adjustment is carried out, the image may not be displayed correctly because of the type of input 
signal.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for 
navigating the picture.
•
Using the remote control
1.
Press MAGNIFY +/- to display the Zoom bar.
2.
Press MAGNIFY + to magnify the center of the picture. Press the key 
repeatedly until the picture size is suitable for your need.
3.
Use the directional arrows ( , 
, 
, 
) on the projector or remote 
control to navigate the picture.
4.
To restore the picture to its original size, press AUTO. You can also 
press MAGNIFY -. When the key is pressed again, the picture is further 
reduced until it is restored to the original size.
•
Using the OSD menu
1.
Press MENU/EXIT and then press 
/  until the DISPLAY menu is highlighted.
2.
Press
 
 to highlight Magnify and press MODE/ENTER. The Zoom bar is displayed.
3.
Repeat steps 2-4 in the section of 
 above. Or if you are using the projector control 
panel, continue to the following steps.
4.
Press   on the projector repeatedly to magnify the picture to a desired size.
5.
To navigate the picture, press MODE/ENTER to switch to the panning mode and press the directional arrows 
( , 
, 
, 
) to navigate the picture.
6.
Use the directional arrows ( , 
, 
, 
) on the projector or remote control to navigate the picture.
7.
To reduce size of the picture, press MODE/ENTER to switch back to the zoom in/out functionality, and press 
AUTO to restore the picture to its original size. You can also press   repeatedly until it is restored to the 
original size.
The picture can only be navigated after the picture is magnified. You can further magnify the picture while searching for details.
Press
/
Press
  / .