Sony STR-DA3100ES Operating Guide
Ope
ra
tions
Us
ing
the
Re
Re
m
o
te
RM-AAE0
0
1
masterpage:Right
lename[E:\SEM_Janet\Revision
Data\J9050000_2514877131STRDA3100ESU\2514877131\GB08REM_STR-DA3100ES-U.fm]
65
US
model name1[STR-DA3100ES]
[2-514-877-13(1)]
6
Press the appropriate button on the
remote control to be learned to send
the remote button code.
remote control to be learned to send
the remote button code.
Lightly pressing the button once should be
sufficient.
If learning is completed successfully, the
indicator slowly flashes twice and the
remote automatically exits the learning
mode.
When learning is not completed
successfully, the indicator flashes 4 times in
quick succession and the procedure returns
to step 6.
If the memory of the remote is already full,
the indicator flashes 8 times in quick
succession and the remote automatically
exits the learning mode.
sufficient.
If learning is completed successfully, the
indicator slowly flashes twice and the
remote automatically exits the learning
mode.
When learning is not completed
successfully, the indicator flashes 4 times in
quick succession and the procedure returns
to step 6.
If the memory of the remote is already full,
the indicator flashes 8 times in quick
succession and the remote automatically
exits the learning mode.
Notes
• You can program more than 80 keys for the Learning
function. In some cases, you may not be able to
program even if you have not programmed 80
buttons. The number of buttons you can program for
each input button are shown in the following table.
program even if you have not programmed 80
buttons. The number of buttons you can program for
each input button are shown in the following table.
button is pressed.
• In step 4, if several buttons that can be used for
learning are pressed, only the last pressed button is
valid. The indicator flashes slowly, it turns ON while
a valid button is pressed.
valid. The indicator flashes slowly, it turns ON while
a valid button is pressed.
• In step 6, if a button that can be used for learning is
pressed, the new button is selected and the learning
procedure returns to the beginning of step 6.
procedure returns to the beginning of step 6.
To activate the input source after
programming
programming
Press the programmed button to activate the
input you want.
input you want.
To cancel learning
Press RM SET UP during any step. The remote
automatically exits the learning mode.
automatically exits the learning mode.
To clear the learned codes
Start over from step 1. After step
, press
TV ?/1 for more than 2 seconds. The indicator
lights up twice slowly and the learned code is
cleared. If TV ?/1 is pressed less than 2
seconds, the learning procedure returns to the
beginning of step 6.
When a learned code is cleared, if the button was
previously programmed for another input
selector, the programmed code for that button
can be used.
lights up twice slowly and the learned code is
cleared. If TV ?/1 is pressed less than 2
seconds, the learning procedure returns to the
beginning of step 6.
When a learned code is cleared, if the button was
previously programmed for another input
selector, the programmed code for that button
can be used.
To clear the memory of the
remote
remote
To clear all programmed and learned signals, do
the following to reset the remote to factory
settings.
the following to reset the remote to factory
settings.
Press ?/1, AV ?/1 and MASTER VOL – at
the same time.
the same time.
The indicator flashes 3 times, then goes off.
To use a command that has been
learned
learned
When selecting a learned input, press the learned
button for that input.
button for that input.
Input
Number of Buttons
you can program
you can program
VIDEO 1, VIDEO 2,
DVD
DVD
78 keys
VIDEO 3, TV/SAT,
TAPE
TAPE
78 keys
MD/DAT, SA-CD/CD,
TUNER
TUNER
78 keys
PHONO, MULTI CH
52 keys
TV buttons, (TV ?/1,
TV VOL +/– , TV CH +/–,
WIDE, TV/VIDEO
TV VOL +/– , TV CH +/–,
WIDE, TV/VIDEO
7 keys
GB01COV_STR-DA3100ES-U.book Page 65 Wednesday, July 13, 2005 2:23 PM