Sony dvp-cx875p User Guide
E:\3077145111DVPCX875P\01US15ADD-
UC.fm
UC.fm
master page=left
DVP-CX875P
3-077-145-11(1)
96
Additional Information
Troubleshooting
If you experience any of the following
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
difficulties while using the player, use this
troubleshooting guide to help remedy the
problem before requesting repairs. Should
any problem persist, consult your nearest
Sony dealer.
Power
The power is not turned on.
, Check that the AC power cord is connected
securely.
Picture
There is no picture/picture noise appears.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, Check the connection to your TV (page 21)
, The connecting cord is damaged.
, Check the connection to your TV (page 21)
and switch the input selector on your TV so
that the signal from the player appears on
the TV screen.
that the signal from the player appears on
the TV screen.
, The disc is dirty or flawed.
, If the picture output from your player goes
, If the picture output from your player goes
through your VCR to get to your TV or if
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV’s S VIDEO input
(page 21).
you are connected to a combination TV/
VIDEO player, the copy-protection signal
applied to some DVD programs could affect
picture quality. If you still experience
problems even when you connect your
player directly to your TV, try connecting
your player to your TV’s S VIDEO input
(page 21).
, You have selected “PROGRESSIVE” in
“COMPONENT OUT” even though your
TV cannot accept the signal in progressive
format. In this case, set the COMPONENT
VIDEO OUTPUT/SCAN SELECT switch
on the back panel of the player to
INTERLACE. When you can see the TV
screen correctly, set “COMPONENT OUT”
to “INTERLACE” and reset the
COMPONENT VIDEO OUTPUT/SCAN
SELECT switch to SELECTABLE.
TV cannot accept the signal in progressive
format. In this case, set the COMPONENT
VIDEO OUTPUT/SCAN SELECT switch
on the back panel of the player to
INTERLACE. When you can see the TV
screen correctly, set “COMPONENT OUT”
to “INTERLACE” and reset the
COMPONENT VIDEO OUTPUT/SCAN
SELECT switch to SELECTABLE.
, Even if your TV is compatible with
progressive format (480p) signals, the
image may be affected when you set
“COMPONENT OUT” to
“PROGRESSIVE.” In this case, set
“COMPONENT OUT” to “INTERLACE.”
image may be affected when you set
“COMPONENT OUT” to
“PROGRESSIVE.” In this case, set
“COMPONENT OUT” to “INTERLACE.”
Even though you set the aspect ratio in “TV
TYPE” of “SCREEN SETUP,” the picture
does not fill the screen.
TYPE” of “SCREEN SETUP,” the picture
does not fill the screen.
, The aspect ratio of the disc is fixed on your
DVD.
Sound
There is no sound.
, Re-connect the connecting cord securely.
, The connecting cord is damaged.
, The player is connected to the wrong input
, The connecting cord is damaged.
, The player is connected to the wrong input
, The amplifier (receiver) input is not
correctly set.
, The player is in pause mode or in Slow-
motion Play mode.
, The player is in fast forward or fast reverse
mode.
, If the audio signal does not come through
Sound is noisy.
, When playing a CD with DTS sound tracks,
noise will come from the AUDIO OUTPUT
L/R 1/2 jacks or DIGITAL OUTPUT
(COAXIAL or OPTICAL) jack (page 34).
L/R 1/2 jacks or DIGITAL OUTPUT
(COAXIAL or OPTICAL) jack (page 34).
Sound distortion occurs.
, Set “AUDIO ATT” in “AUDIO SETUP” to
“ON” (page 93).
The sound volume is low.
, The sound volume is low on some DVDs.
The sound volume may improve if you set
“AUDIO DRC” to “TV MODE” (page 93).
“AUDIO DRC” to “TV MODE” (page 93).
, Set “AUDIO ATT” in “AUDIO SETUP” to
“OFF” (page 93).