NEC GT5000 Reference Guide
VT770
Control Codes
Function
Code
Data
POWER
ON
02H 00H 00H 00H 00H 02H
POWER
OFF
02H 01H 00H 00H 00H 03H
INPUT
SELECT
COMPUTER
1
02H 03H 00H 00H 02H 01H 01H 09H
INPUT
SELECT
COMPUTER
2
02H 03H 00H 00H 02H 01H 02H 0AH
INPUT
SELECT
VIDEO
02H 03H 00H 00H 02H 01H 06H 0EH
INPUT
SELECT
S-VIDEO
02H 03H 00H 00H 02H 01H 0BH 13H
INPUT
SELECT
COMPONENT
02H 03H 00H 00H 02H 01H 1AH 22H
INPUT
SELECT
VIEWER 02H 03H 00H 00H 02H 01H 1FH 27H
PICTURE
MUTE
ON
02H 10H 00H 00H 00H 12H
PICTURE
MUTE
OFF
02H 11H 00H 00H 00H 13H
SOUND
MUTE
ON
02H 12H 00H 00H 00H 14H
SOUND
MUTE
OFF
02H 13H 00H 00H 00H 15H
ON
SCREEN
MUTE
ON
02H 14H 00H 00H 00H 16H
ON
SCREEN
MUTE
OFF 02H 15H 00H 00H 00H 17H
ASPECT
RATIO
(4:3
Screen) 4:3
03H 10H 00H 00H 05H 18H 00H 00H 00H 00H 30H
Letterbox
03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H
Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H
Crop
Crop
03H 10H 00H 00H 05H 18H 00H 00H 03H 00H 33H
ASPECT RATIO (16:9 Screen) 4:3 Window 03H
10H 00H 00H 05H 18H 00H 00H 00H 00H 30H
Letterbox
03H 10H 00H 00H 05H 18H 00H 00H 01H 00H 31H
Widescreen 03H 10H 00H 00H 05H 18H 00H 00H 02H 00H 32H
4:3
4:3
Fill
03H 10H 00H 00H 05H 18H 00H 00H 04H 00H 34H
AUTO
ADJUST
02H 0FH 00H 00H 02H 05H 00H 18H
Note: Contact your NEC rep for codes not listed.
Cable Connection
Communication
Protocol:
PC
Control
Connector
(D-Sub
9p)
Baud Rate:
38400 bps
Data Length:
8 bits
1
2
3
4
5
6
7
8
9
To GND of PC
To RxD of PC
To TxD of PC
To CTS of PC
To RTS of PC
Parity:
No
Parity
Stop Bit:
One bit
X
on/off:
None
Communications: Full duplex
NOTE1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.
NOTE2: Pins 1, 4, 6, and 9 are used inside the projector.
NOTE3: Jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu.
NOTE1: It is recommended to set the projector to “Idle Mode” in the Setup menu for best Power ON response.
NOTE2: Pins 1, 4, 6, and 9 are used inside the projector.
NOTE3: Jumper “Request to send” and “Clear to Send” together on both ends of the cable to simplify cable connection.
NOTE4: For long cable runs it is recommended to set communication speed to 9600 bps in the Setup menu.