Sony ht-ddw1500 User Guide
76
GB
C:\Documents and
Settings\pc13\Desktop\JC060815_2662266612DDW1500_GBES\2662266612\01GB05AMP_HT-
DDW1500-AR.fm
Settings\pc13\Desktop\JC060815_2662266612DDW1500_GBES\2662266612\01GB05AMP_HT-
DDW1500-AR.fm
masterpage: Left
HT-DDW1500
2-662-266-61 (2)
(Except for models of area code MX, E51,
AR)
AR)
The source image input to the HDMI jack
on the receiver is not output from the TV.
on the receiver is not output from the TV.
• Check the HDMI connection.
• Depending on the playback component,
• Depending on the playback component,
you may need to set up the component.
Refer to the operating instructions
supplied with the each component.
Refer to the operating instructions
supplied with the each component.
• Assign the HDMI input correctly.
The MULTI CHANNEL DECODING lamp
does not light up.
does not light up.
• Check that the playback component is
connected to a digital jack and the input is
selected properly on this receiver.
selected properly on this receiver.
• Check whether the input source of the
software being played back corresponds to
the multi channel format.
the multi channel format.
• Check whether the setup on the playback
component is set to multi channel sound.
Remote control
The remote does not function.
• The AUX and 12 buttons on the remote are
not available for receiver operation.
• Point the remote at the remote sensor on
the receiver.
• Remove any obstacles in the path between
the remote and the receiver.
• Replace all the batteries in the remote with
new ones, if they are weak.
• Make sure you select the correct input on
the remote.
Error messages
If there is a malfunction, the display shows a
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer. If an
error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 34) to solve the problem.
message. You can check the condition of the
system by the message. Refer to the following
table to solve the problem. If any problem
persists, consult your nearest Sony dealer. If an
error message appears while you perform
Auto Calibration, see “Error and warning
codes” (page 34) to solve the problem.
DEC. EROR
Appears when a signal the receiver cannot
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 42).
decode (ex. DTS-CD) is input and “DEC.
PRI.” on the AUDIO menu is set to “DEC.
PCM”. Set it to “DEC. AUTO” (page 42).
PROTECT
Irregular current is output from the
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
speakers. The receiver will automatically
turn off after a few seconds. Check the
speaker connection and turn on the power
again.
If you are unable to remedy the
problem using the
troubleshooting guide
problem using the
troubleshooting guide
Clearing the receiver’s memory may remedy
the problem (page 31). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
the problem (page 31). However, note that all
memorized settings will be reset to their
factory settings and you will have to readjust
all settings on the receiver.
If the problem persist
Consult your nearest Sony dealer. Note that if
service personnel changes some parts during
repair, these parts may be retained.
service personnel changes some parts during
repair, these parts may be retained.
Reference sections for clearing
the receiver’s memory
the receiver’s memory
To clear
See
All memorized settings
page 31
Customized sound fields
page 57
01GB01COV_HT-DDW1500-AR.book Page 76 Tuesday, May 23, 2006 6:27 PM